yashim / open-evse Goto Github PK
View Code? Open in Web Editor NEWAutomatically exported from code.google.com/p/open-evse
Automatically exported from code.google.com/p/open-evse
What steps will reproduce the problem?
1. Charge car.
2. Unplug car.
3. Note watts and cumulative watts.
4. Press button for sleep or menus.
5. Return from menus or sleep.
What is the expected output? What do you see instead?
Expected:
Don't know exactly, where's instructions? but guess that the last charge should
go to zero while the cumulative increments by last amount. Or last charge
remains until next charge but doesn't get added to cumulative every time you
press the button to initiate sleep or menus.
See:
Last charge remains and gets added to cumulative every time I enter and leave
sleep or menus.
What version of the product are you using? V2.5, firmware 3.9.0
On what operating system? mac OSX
Please provide any additional information below.
Original issue reported on code.google.com by [email protected]
on 12 Jul 2015 at 7:00
What steps will reproduce the problem?
1. Turn off any adafruit or i2c display defines (IOW, only anticipate CLI usage
with no display)
2. Attempt to compile the code
3. g_psEnabled[] is not defined in any scope yet used in CLI::GetInput
I believe if one moves
prog_char g_psEnabled[] PROGMEM = "enabled";
prog_char g_psDisabled[] PROGMEM = "disabled";
to AFTER
#endif // LCD16X2
but BEFORE
//-- end global variables
void EvseReset();
(sorry I didn't attach a diff; I'll git it into that later)
Original issue reported on code.google.com by [email protected]
on 30 Aug 2012 at 5:23
What steps will reproduce the problem?
Simply check communication after fixing PCB reset issue (missing connection)
1. avrdude -c usbtiny -p m328p
What is the expected output? What do you see instead?
avrdude: Device signature = 0x1e9514
avrdude: Expected signature for ATMEGA328P is 1E 95 0F
What version of the product are you using? On what operating system?
V.4
Please provide any additional information below.
Corrected PCB bug of missing Reset connection to Pin1 Atmel328p
Firmware seems not loaded (board is not working yet
Original issue reported on code.google.com by [email protected]
on 15 Mar 2013 at 1:23
Attachments:
What steps will reproduce the problem?
1. Connect Smart ED to EVSE
2. Set EVSE on via RAPI "FE"
3. Set EVSE sleeping "FS"
4. Set EVSE on via RAPI "FE" within 60 sek
Smart ED LED on Charging Socket flasching red.
I think the problem is that the EVSE goes to status disabled and disconnects
the reails.
What is the expected output? What do you see instead?
when EVSE is set to sleeping, don´t open the relais and set state to disabled.
Sleeping means, that the it is possible to start the charging immediately.
Maybe it is useful to make a new Command on Rapi -> "Soft Stop"
What version of the product are you using? On what operating system?
OpenEVSE Plus DIY
Please provide any additional information below.
Original issue reported on code.google.com by [email protected]
on 15 Jan 2015 at 1:43
The Tesla Roadster is sensitive to voltages on the lower end off the J1772
State Voltages.
Original issue reported on code.google.com by chris1howell83
on 2 Jul 2012 at 9:52
What is the part number and supplier of RELAYPTH3?
Original issue reported on code.google.com by jappelbaum1
on 18 Oct 2013 at 1:24
What steps will reproduce the problem?
1. Enable the AdaFruit RGBLCD definitions in the source code.
2. Compile and load the Hex file into the EVSE
3. Do not plug in the LCD to the i2c header
4. Power on the EVSE
What is the expected output? What do you see instead?
Car should charge in spite of not having a display operating. EVSE does not
communicate with vehicle and does not charge the car.
Please use labels and text to provide additional information.
Workaround: Compile the source code with RGBLCD definitions disabled if you are
not using an LCD display. Otherwise, connect the LCD prior to powering up the
system.
Original issue reported on code.google.com by [email protected]
on 3 Feb 2013 at 12:32
SYMPTOMS/ENVIRONMENT:
After plugging vehicle into the open-evse (v4 hardware & v1.0.9 firmware), the
state is perpetually "EV Connected - EVSE Ready". The EVSE will not advance to
the "Charging" state.
Additional symptoms are the boot up sequence takes about 10 seconds (as opposed
to about 1 second normally) and it causes the pilot pwm frequency to be ~60Hz
instead of 1kHz (seen with a DMM or oscilloscope).
ISSUE:
This occurred after programming a virgin atmega328p using the ICSP and the
Arduino IDE by following the instructions at
https://code.google.com/p/open-evse/wiki/LoadingFirmware and
http://blog.lincomatic.com/?p=10.
The reason for this occurring is that following this specific programming
process, the AVR fuses are not set causing the micro-controller's clock to run
too slow.
WORKAROUND:
Follow the instructions specifically for setting the fuses on
https://code.google.com/p/open-evse/wiki/AVRDUDE
Original issue reported on code.google.com by [email protected]
on 16 Mar 2013 at 10:20
What steps will reproduce the problem?
early Open EVSE boards with no vias (small gold colored circles) next to the
large tab of the regulator.
What is the expected output? What do you see instead?
Regulator should not be so warm
To allow the regulator to disipate more heat into the ground plane, scrape away
the coating to expose the copper layer above the large tab of the regulator.
Then solder the ground plane and allow it to flow to the large tab.
The regulator will run much cooler.
Expose Copper
<a href="http://www.flickr.com/photos/60192309@N05/6887966107/"
title="2012-02-16_09-09-44_661 by chris1howell, on Flickr"><img
src="http://farm8.staticflickr.com/7185/6887966107_7464d897c9_z.jpg"
width="640" height="360"></a>
Solder to tab
<a href="http://www.flickr.com/photos/60192309@N05/6887959063/"
title="2012-02-16_09-09-57_873 by chris1howell, on Flickr"><img
src="http://farm8.staticflickr.com/7064/6887959063_e2dd245600_z.jpg"
width="640" height="360"></a>
Original issue reported on code.google.com by chris1howell83
on 16 Feb 2012 at 9:23
What steps will reproduce the problem?
1. Reboot device
2. cycle programing button
3.
What is the expected output? What do you see instead? The backlight to remain
on or change color, when charging the backlight goes out completely, still able
with a light to see text.
What version of the product are you using? On what operating system? OpenEV Ver
3 board with sw ver 3.3.4
Please provide any additional information below.
Using the 220 volt contactor/relay
Original issue reported on code.google.com by [email protected]
on 21 Mar 2015 at 6:06
While assembling the OpenEVSE LCD - DIY Kit, there was a misalignment in the
definition of the resistors R1, R2, and R3.
On the board, the following values are declared:
R1=220, R2=330, R3=220 [ohm]
The resistors received in the kit are:
two resistors colored (yellow-white-white-gold-brown.
one resistor colored (brown-blue-black-gold-brown).
What is the correct value and position on the board? (is there an error in the
bard?)
Anyone who has a working system and can share the correct placement with us?
Thanks, Yoni.
Link to the relevant guide:
https://code.google.com/p/open-evse/wiki/OpenEVSE_DIY_LCD_spec
Original issue reported on code.google.com by [email protected]
on 31 May 2014 at 9:27
I am building a triphase portable EVSE with a type 2 socket, using the open
EVSE that cannot be praised enough.
I have one question though: where should I connect the pp-contact of the
socket? I guess it should be connected to ground, but could someone confirm
this? It might be a good idea to mention this in the manual. I also noticed
that in most projects, the pp is not connected at all.
Many thanks,
Filip
Original issue reported on code.google.com by [email protected]
on 16 Apr 2014 at 7:52
Attachments:
What steps will reproduce the problem?
1. Turn on EVSE with CLI enabled and LCD atttached, no HV
2. Verify LCD says "L1:12a"
3. In CLI change amps to 16, save. CLI doesn't change. Power cycling will show
the new setting.
What is the expected output? What do you see instead?
LCD display of amp setting should change as it is changed in CLI.
What version of the product are you using? On what operating system?
1.0.3
Please provide any additional information below.
Original issue reported on code.google.com by [email protected]
on 5 Sep 2012 at 1:37
What steps will reproduce the problem?
Elapsed timer gone when charging is complete
What is the expected output? What do you see instead?
Elapsed Timer should stop counting up when charging is complete and continue to
display the total elapsed time of the charge until the charge cable is
unplugged.
Original issue reported on code.google.com by chris1howell83
on 15 Oct 2013 at 12:22
SYMPTOMS/ENVIRONMENT:
When attempting to upload the open_evse.pde to an open-evse V4 board (from OSH
PARK direct purchase) with the Arduino IDE and a USBtinyISP, the following
avrdude error occurs:
"initialization failed, rc=-1"
ISSUE:
It appears that the "RST" trace from pin 5 of the ISP1 header (J1) to pin 1 of
IC1 is missing. This was evident in the board file: "Open EVSEv4.brd" and may
have occurred because of the label mismatch (RST vs RESET) in the schematic:
"Open EVSEv4.sch".
WORKAROUND:
After adding a jumper in place of the missing trace, upload was successful.
Original issue reported on code.google.com by [email protected]
on 10 Mar 2013 at 6:13
A declarative, efficient, and flexible JavaScript library for building user interfaces.
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google ❤️ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.