Table of Contents generated with DocToc
- ansible-rpi-k8s-cluster
This repo will be used for deploying a Kubernetes cluster on Raspberry Pi using Ansible.
I have been looking at putting together a Kubernetes cluster using Raspberry
Pi's for a while now. And I finally pulled all of it together and started pulling
together numerous Ansible
roles which I had already developed over time. I
wanted this whole project to be provisioned with Ansible
so I had a repeatable
process to build everything out. As well as a way to share with others. I am
still putting all of the pieces together so this will no doubt be a continual
updated repo for some time.
The following will outline the design of how this current iteration works.
Basically we have a 5 (or more) node Raspberry Pi cluster. With the first node
connecting to wireless to act as our gateway into the cluster. The first node is
by far the most critical. We use the first nodes wireless connection to also do
all of our provisioning of our cluster. We execute Ansible
against all of the
remaining nodes by using the first node as a bastion host via it's wireless IP.
Once you obtain the IP of the first node's wireless connection you need to
update jumphost_ip:
in inventory/group_vars/all/all.yml
as well as change the ansible_host
for rpi-k8s-1 ansible_host=172.16.24.186
in inventory/hosts.inv. If you would like to change the
subnet which the cluster will use, change dhcp_scope_subnet:
in inventory/group_vars/all/all.yml
to your desired subnet as well as the ansible_host
addresses for the following
nodes in inventory/hosts.inv:
[rpi_k8s_slaves]
rpi-k8s-2 ansible_host=192.168.100.128
rpi-k8s-3 ansible_host=192.168.100.129
rpi-k8s-4 ansible_host=192.168.100.130
rpi-k8s-5 ansible_host=192.168.100.131
NOTE: We may change to an automated inventory being generated if it makes things a little more easy.
The first node provides the following services for our cluster:
- DHCP for all of the other nodes (only listening on
eth0
) - Gateway services for other nodes to connect to the internet and such.
- An IPTABLES Masquerade rule NATs traffic from
eth0
throughwlan0
- An IPTABLES Masquerade rule NATs traffic from
- Apt-Cacher NG - A package caching proxy to speed up package downloads/installs.
NOTE: You can also define a static route on your LAN network firewall (if supported) for the subnet (
192.168.100.0/24
in my case) to the wireless IP address that your first node obtains. Or you may add a static route on your Ansible control machine. This will allow you to communicate with all of the cluster nodes once they get an IP via DHCP from the first node.
For Kubernetes networking we are using Weave Net.
The following is a list of the required packages to be installed on your Ansible
control machine (the machine you will be executing Ansible from).
You can install Ansible
in many different ways so head over to the official
Ansible
intro installation.
You will also need to install the kubectl
package. As with Ansible
there are many different ways to install kubectl
so head over to the official
Kubernetes
Install and Set Up kubectl.
NOTE: The Ansible playbook playbooks/deployments.yml fetches the
admin.conf
from the K8s master and copies this to your local $HOME/.kube/config. This allows us to runkubectl
commands remotely to the cluster. There is a catch here though. The certificate is signed with the internal IP address of the K8s master. So in order for this to work correctly you will need to setup a static route on your firewall (if supported) to the subnet192.168.100.0/24
(in our case) via the wireless IP on your first node (also the K8s master). Or you may add a static route on your Ansible control machine.
The following list is the hardware which I am using currently while developing this.
- 5 x Raspberry Pi 3
- 2 x 6pack - Cat 6 - Flat Ethernet Cables
- 1 x Anker PowerPort 6 - 60W 6-Port Charging Hub
- 5 x Samsung 32GB 95MB/s MicroSD Evo Memory Card
- 1 x GeauxRobot Raspberry Pi 3 5-Layer Dog Bone Stack Case
- 1 x 8-Port Ethernet Switch
Currently I am using Raspbian Lite for the OS. I did not orginally go with Hyperiot intentionally but may give it a go at some point.
Head over here and download
the RASPBIAN STRETCH LITE
image.
I am using a Mac so my process will based on that so you may need to adjust based on your OS.
After you have finished downloading the OS you will want to
extract the zip file 2017-11-29-raspbian-stretch-lite.zip
in my case. After
extrating the file you are ready to load the OS onto each and every SD card. In
my case I am paying special attention to the first one. The first one we will be
adding the wpa_supplicant.conf
file which will connect us to wireless. We will
use wireless as our gateway into the cluster. We want to keep this as isolated
as possible.
With our zip file extracted we are now ready to load the image onto our SD card. Remember what I mentioned above, the first one is the one which we will use to connect to wireless.
NOTE: Remember I am using a Mac so YMMV! You may also want to look into Etcher or PiBakery for a GUI based approach.
Open up your terminal and execute the following to determine the device name of the SD card:
diskutil list
...
/dev/disk0 (internal, physical):
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *500.3 GB disk0
1: EFI EFI 209.7 MB disk0s1
2: Apple_CoreStorage macOS 499.4 GB disk0s2
3: Apple_Boot Recovery HD 650.0 MB disk0s3
/dev/disk1 (internal, virtual):
#: TYPE NAME SIZE IDENTIFIER
0: Apple_HFS macOS +499.0 GB disk1
Logical Volume on disk0s2
7260501D-EA09-4048-91FA-3A911D627C9B
Unencrypted
/dev/disk2 (external, physical):
#: TYPE NAME SIZE IDENTIFIER
0: FDisk_partition_scheme *32.0 GB disk2
1: DOS_FAT_16 NEW VOLUME 32.0 GB disk2s1
From the above in my case I will be using /dev/disk2
which is my SD card.
Now we need to unmount the disk so we can write to it:
diskutil unmountdisk /dev/disk2
Now that our SD card is unmounted we are ready to write the OS image to it. And we do that by running the following in our terminal:
sudo dd bs=1m if=/Users/larry/Downloads/2017-11-29-raspbian-stretch-lite.img of=/dev/disk2 conv=sync
After that completes we now need to remount the SD card so that we can write some files to it.
diskutil mountdisk /dev/disk2
First we need to create a blank file ssh
onto the SD card to enable SSH when
the Pi boots up.
touch /Volumes/boot/ssh
Next we need to create the wpa_supplicant.conf
file which will contain the
configuration to connect to wireless. The contents of this file are listed below:
vi /Volumes/boot/wpa_supplicant.conf
wpa_supplicant.conf
:
country=US
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
network={
ssid="your_real_wifi_ssid"
scan_ssid=1
psk="your_real_password"
key_mgmt=WPA-PSK
}
Now that you have finished creating these files you can then unmount the SD card:
diskutil unmountdisk /dev/disk2
Now set this first one aside or place it into your Raspberry Pi that you want to be the first node.
For the remaining SD cards you will follow the same process as in First SD Card
except you will not create the wpa_supplicant.conf
file on these. Unless you
want to use wireless for all of your Pi's. If that is the case then that will be
out of scope for this project (for now!).
Most variables that need to be adjusted based on deployment can be found in
inventory/group_vars/all/all.yml. Make sure
to update jumphost_ip
to the IP address that your first node obtained via DHCP
and rpi_nodes
to define the number of cluster nodes. If you do not define the
rpi_nodes
correctly and you fire up all of your cluster nodes. After the first
node is provisioned for DHCP we wait for the number of DHCP leases to equal the
number of cluster nodes (minus the first node). So if this is incorrect,
provisioning will fail. So keep that in mind.
NOTE: We are using our cluster as cattle and not pets here folks. If you want to hand hold your cluster nodes then you will need to go to further extents beyond what this project is about. The only pet we have here is our first cluster node. This is because we need to know which one we need to connect to wireless, and which one routes, provides DHCP, and etc.
By default we are using DNSMasq
now to provide DHCP for the cluster nodes.
(Note: The first cluster node does not get it's address via DHCP, it is statically assigned)
Being that we are using DHCP for the cluster nodes we need to first make sure
that we account for the number of cluster nodes we are using. With this being
said, we need to adjust a few variables and the inventory to account for this.
The assumption within this project is that we are using 5 cluster nodes which is
how DHCP is configured to accomodate such.
The important things to ensure that are configured correctly are listed below:
You should change the dhcp_scope_subnet: 192.168.100
, dhcp_scope_start_range: "{{ dhcp_scope_subnet }}.128"
, dhcp_scope_end_range: "{{ dhcp_scope_subnet }}.131"
, and rpi_nodes
variables to meet your requirements. Please review ansible-variables
for further explanation on the importance of rpi_nodes
.
# Defines DHCP scope end address
dhcp_scope_end_range: "{{ dhcp_scope_subnet }}.131"
# Defines DHCP scope start address
dhcp_scope_start_range: "{{ dhcp_scope_subnet }}.128"
# Defines dhcp scope subnet for isolated network
dhcp_scope_subnet: 192.168.100
# Defines the number of nodes in cluster
# Extremely important to define correctly, otherwise provisioning will fail.
rpi_nodes: 5
Based on the above we can ensure that we are only handing out 4
IP addresses
to the cluster nodes because the first node again is statically assigned. This
will account for our 5
node cluster. So if you have a different number of cluster
nodes then you will need to adjust the start and end ranges. Why is this important?
Because we can then ensure that we can define our inventory appropriately. And
because we are treating all but our first node as cattle, we do not care which
one in the stack is which, just as long as we can assign addresses to them and we
can provision them.
Now, based on the details from above we need to ensure that our inventory is
properly configured. So make sure that your inventory matches the DHCP range
you defined and the nodes for the group rpi_k8s_slaves
is accurate. Remembering
that we are treating our slaves as cattle.
[rpi_k8s_slaves]
rpi-k8s-2 ansible_host=192.168.100.128
rpi-k8s-3 ansible_host=192.168.100.129
rpi-k8s-4 ansible_host=192.168.100.130
rpi-k8s-5 ansible_host=192.168.100.131
To provision the full stack you can run the following:
ansible-playbook -i inventory playbooks/deploy.yml
If you happen to get the following error when attempting to deploy:
TASK [Gathering Facts] ***********************************************************************************************************************************************************
Sunday 11 February 2018 04:56:29 +0000 (0:00:00.029) 0:00:00.127 *******
fatal: [rpi-k8s-1]: FAILED! => {"msg": "to use the 'ssh' connection type with passwords, you must install the sshpass program"}
to retry, use: --limit @/home/vagrant/ansible-rpi-k8s-cluster/playbooks/deploy.retry
Head over to here to resolve that issue.
If you happen to get the following error when attempting to deploy:
TASK [Adding Local User SSH Key] *************************************************************************************************************************************************
Sunday 11 February 2018 04:58:28 +0000 (0:00:00.022) 0:00:34.350 *******
[WARNING]: Unable to find '/home/vagrant/.ssh/id_rsa.pub' in expected paths.
fatal: [rpi-k8s-1]: FAILED! => {"msg": "An unhandled exception occurred while running the lookup plugin 'file'. Error was a <class 'ansible.errors.AnsibleError'>, original message: could not locate file in lookup: /home/vagrant/.ssh/id_rsa.pub"}
to retry, use: --limit @/home/vagrant/ansible-rpi-k8s-cluster/playbooks/deploy.retry
You will need to generate an SSH key for your local user that you are running Ansible as:
ssh-keygen
...
Generating public/private rsa key pair.
Enter file in which to save the key (/home/vagrant/.ssh/id_rsa):
Enter passphrase (empty for no passphrase):
Enter same passphrase again:
Your identification has been saved in /home/vagrant/.ssh/id_rsa.
Your public key has been saved in /home/vagrant/.ssh/id_rsa.pub.
The key fingerprint is:
SHA256:pX5si9jHbpe2Ubss4eLjGlMs7J3iC7PHOwkiDCkPE74 vagrant@node0
The key's randomart image is:
+---[RSA 2048]----+
| |
|. |
|.o . |
|*. . + |
|.*. S o . |
| E+ . .o = ... . |
| . .oo*o*..o. |
| B=B*.*o . |
| o.B@==.oo |
+----[SHA256]-----+
To manage the WI-FI connection on your first node. You can create a wifi.yml
file in inventory/group_vars/all
with the following defined variables:
NOTE:
wifi.yml
is added to the.gitignore
to ensure that the file is excluded from Git. Use your best judgment here. It is probably a better idea to encrypt this file withansible-vault
. The task(s) to manage WI-FI are in playbooks/bootstrap.yml and will only trigger if the variables defined below exist.
k8s_wifi_country: US
k8s_wifi_password: mysecretwifipassword
k8s_wifi_ssid: mywifissid
CAUTION: If your WI-FI IP address changes,
Ansible
will fail as it will no longer be able to connect to the original IP address. Keep this in mind.
If you would like to simply manange the WI-FI connection you may run the following:
ansible-playbook -i inventory playbooks/bootstrap.yml --tags rpi-manage-wifi
In order to use kubectl
from your Ansible control machine, you need to ensure
that you have a static route either on your LAN firewall or your local routing
table on your Ansible control machine.
In order to add a static route on you will need to do the following:
NOTE: Replace
172.16.24.186
with the IP of that your first node obtained via DHCP. Also update192.168.100.0/24
with the subnet that you changed the variabledhcp_scope_subnet
ininventory/group_vars/all/all.yml
to if you changed it.
sudo route -n add 192.168.100.0/24 172.16.24.186
...
Password:
add net 192.168.100.0: gateway 172.16.24.186
You can verify that the static route is definitely configured by executing the following:
netstat -nr | grep 192.168.100
...
192.168.100 172.16.24.186 UGSc 0 0 en0
If you decide to delete the static route you can do so by executing the following:
sudo route -n delete 192.168.100.0/24 172.16.24.186
...
Password:
delete net 192.168.100.0: gateway 172.16.24.186
We have included Traefik as an available load balancer which can be deployed to expose cluster services.
You can deploy Traefik
by running the following:
kubectl apply -f deployments/traefik.yaml
You can access the Traefik WebUI by heading over to http://wirelessIP:8080/dashboard/#/
(replace wirelessIP
with your actual IP of the wireless address on the first node).
We have an example NGINX deployment deployments/nginx_deployment.yaml
that you can easily spin up for learning and testing. This deployment creates
the demo
Namespace, nginx-demo
Deployment with 2
replicas using the nginx
image, nginx-demo
Service, nginx-demo
Ingress, and attaches itself to the Traefik
load balancer with the path /demo
but strips the path prefix so that the default
NGINX container(s) will return the default page as /
rather than /demo
because
that would fail. You can then connect to the default web page by connecting to
http://wirelessIP/demo.
To spin up this demo simply execute the following:
kubectl apply -f deployments/nginx_deployment.yaml
To validate all is good:
kubectl get all --namespace demo
...
NAME DESIRED CURRENT UP-TO-DATE AVAILABLE AGE
deploy/nginx-demo 2 2 2 2 11m
NAME DESIRED CURRENT READY AGE
rs/nginx-demo-76c897787b 2 2 2 11m
NAME DESIRED CURRENT UP-TO-DATE AVAILABLE AGE
deploy/nginx-demo 2 2 2 2 11m
NAME DESIRED CURRENT READY AGE
rs/nginx-demo-76c897787b 2 2 2 11m
NAME READY STATUS RESTARTS AGE
po/nginx-demo-76c897787b-gzwgl 1/1 Running 0 11m
po/nginx-demo-76c897787b-pzfrl 1/1 Running 0 11m
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
svc/nginx-demo ClusterIP 10.102.204.13 <none> 80/TCP 11m
To tear down this demo simply execute the following:
kubectl delete -f deployments/nginx_deployment.yaml
We have included the Kubernetes dashboard as part of the provisioning. By default the dashboard is only available from within the cluster. So in order to connect to it you have a few options.
If you have installed kubectl
on your local machine then you can simply drop
to your terminal and type the following:
kubectl proxy
...
Starting to serve on 127.0.0.1:8001
Now you can open your browser of choice and head here
NOTE: This method will also only work if you have a static route into the cluster subnet
192.168.100.0/24
.
You can also use an SSH tunnel to your Kubernetes master node (any cluster node
will work, but because the assumption is that the first node will be the only one
accessible over WI-FI). First you need to find the kubernetes-dashboard
ClusterIP, and you can do that by executing the following:
kubectl get svc --namespace kube-system kubernetes-dashboard
...
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
kubernetes-dashboard ClusterIP 10.106.41.154 <none> 443/TCP 2d
And from the above you will see that the ClusterIP is 10.106.41.154
. Now you
can create the SSH tunnel as below:
ssh -L 8001:10.106.41.154:443 [email protected]
Now you can open your browser of choice and head here
If you would like to allow admin privileges without requiring either a kubeconfig
or token then you can apply the following ClusterRoleBinding
:
NOTE: You can find more details on this here.
kubectl apply -f deployments/dashboard-admin.yaml
And now when you connect to the dashboard you can click skip and have full admin
access. This is obviously not good practice, so you should delete this
ClusterRoleBinding
when you are done:
kubectl delete -f deployments/dashboard-admin.yaml
You may wish to update the default DNS
service to use CoreDNS
to learn and/or
whatever you want. The good news is that CoreDNS
will eventually be the default
DNS
replacing kube-dns
. So may as well start testing now!
NOTE: CoreDNS can run in place of the standard Kube-DNS in Kubernetes. Using the kubernetes plugin, CoreDNS will read zone data from a Kubernetes cluster.
If you would like to replace the default DNS
service installed during
provisioning with CoreDNS
, you can easily do so by doing the following:
cd deployments
./deploy-coredns.sh | kubectl apply -f -
kubectl delete --namespace=kube-system deployment kube-dns
The following can be used if you would rather use kubeadm
to update your
cluster to use CoreDNS
rather than using the kubectl
method above. First you
should check to make sure that this method is possible within your cluster.
kubeadm upgrade plan --feature-gates CoreDNS=true
...
[preflight] Running pre-flight checks.
[upgrade] Making sure the cluster is healthy:
[upgrade/config] Making sure the configuration is correct:
[upgrade/config] Reading configuration from the cluster...
[upgrade/config] FYI: You can look at this config file with 'kubectl -n kube-system get cm kubeadm-config -oyaml'
[upgrade] Fetching available versions to upgrade to
[upgrade/versions] Cluster version: v1.9.3
[upgrade/versions] kubeadm version: v1.9.2
[upgrade/versions] Latest stable version: v1.9.3
[upgrade/versions] Latest version in the v1.9 series: v1.9.3
Awesome, you're up-to-date! Enjoy!
Checking pod
status:
kubectl get pods --namespace kube-system -o wide
...
NAME READY STATUS RESTARTS AGE IP NODE
coredns-7f969bcf8c-458jv 1/1 Running 0 22m 10.34.0.3 rpi-k8s-4
coredns-7f969bcf8c-nfpf7 1/1 Running 0 22m 10.40.0.3 rpi-k8s-5
etcd-rpi-k8s-1 1/1 Running 0 4d 192.168.100.1 rpi-k8s-1
heapster-8556df7b6b-cplz6 1/1 Running 0 4d 10.34.0.0 rpi-k8s-4
kube-apiserver-rpi-k8s-1 1/1 Running 2 4d 192.168.100.1 rpi-k8s-1
kube-controller-manager-rpi-k8s-1 1/1 Running 2 4d 192.168.100.1 rpi-k8s-1
kube-proxy-644h6 1/1 Running 0 4d 192.168.100.130 rpi-k8s-4
kube-proxy-8dfbr 1/1 Running 0 4d 192.168.100.1 rpi-k8s-1
kube-proxy-fcpqp 1/1 Running 0 4d 192.168.100.131 rpi-k8s-5
kube-proxy-kh4jq 1/1 Running 0 4d 192.168.100.128 rpi-k8s-2
kube-proxy-tjckk 1/1 Running 0 4d 192.168.100.129 rpi-k8s-3
kube-scheduler-rpi-k8s-1 1/1 Running 2 4d 192.168.100.1 rpi-k8s-1
kubernetes-dashboard-6686846dfd-z62q4 1/1 Running 0 4d 10.40.0.0 rpi-k8s-5
monitoring-grafana-6859cdd4bd-7bk5c 1/1 Running 0 4d 10.45.0.0 rpi-k8s-3
monitoring-influxdb-59cb7cb77b-rpmth 1/1 Running 0 4d 10.46.0.0 rpi-k8s-2
tiller-deploy-6499c74d46-hjgcr 1/1 Running 0 2d 10.40.0.1 rpi-k8s-5
traefik-ingress-controller-6ffd67bfcf-wb5m2 1/1 Running 0 2d 192.168.100.1 rpi-k8s-1
weave-net-7xfql 2/2 Running 12 4d 192.168.100.1 rpi-k8s-1
weave-net-kxw2h 2/2 Running 2 4d 192.168.100.129 rpi-k8s-3
weave-net-rxsfg 2/2 Running 2 4d 192.168.100.128 rpi-k8s-2
weave-net-rzwd2 2/2 Running 2 4d 192.168.100.131 rpi-k8s-5
weave-net-wnk26 2/2 Running 2 4d 192.168.100.130 rpi-k8s-4
Checking deployment
status:
kubectl get deployment --namespace kube-system
...
NAME DESIRED CURRENT UP-TO-DATE AVAILABLE AGE
coredns 2 2 2 2 28m
heapster 1 1 1 1 4d
kubernetes-dashboard 1 1 1 1 4d
monitoring-grafana 1 1 1 1 4d
monitoring-influxdb 1 1 1 1 4d
tiller-deploy 1 1 1 1 2d
traefik-ingress-controller 1 1 1 1 2d
Checking dig
results:
First you need to find the CLUSTER-IP
:
kubectl get service --namespace kube-system kube-dns
...
NAME TYPE CLUSTER-IP EXTERNAL-IP PORT(S) AGE
kube-dns ClusterIP 10.96.0.10 <none> 53/UDP,53/TCP 50m
Now you can use dig
:
dig @10.96.0.10 default.svc.cluster.local +noall +answer
...
; <<>> DiG 9.10.3-P4-Raspbian <<>> @10.96.0.10 default.svc.cluster.local +noall +answer
; (1 server found)
;; global options: +cmd
default.svc.cluster.local. 5 IN A 10.45.0.2
default.svc.cluster.local. 5 IN A 10.96.0.1
default.svc.cluster.local. 5 IN A 10.34.0.2
default.svc.cluster.local. 5 IN A 10.109.20.92
We have also enabled Helm as part of the provisioning of the cluster. However, because we are using Raspberry Pi's and Arm architecture we need to make some adjustments post deployment.
kubectl create serviceaccount --namespace kube-system tiller
kubectl create clusterrolebinding tiller-cluster-rule --clusterrole=cluster-admin --serviceaccount=kube-system:tiller
kubectl patch deploy --namespace kube-system tiller-deploy -p '{"spec":{"template":{"spec":{"serviceAccount":"tiller"}}}}'
kubectl set image deploy/tiller-deploy tiller=luxas/tiller:v2.6.1 --namespace kube-system
We have included GlusterFS as backend for persistent
storage to be used by containers. We are not using Heketi
at this time. So all managment of GlusterFS
is done via Ansible
. Check out
the group_vars
in inventory/group_vars/rpi_k8s/glusterfs.yml
to define the backend bricks and client mounts.
GlusterFS can also be defined to be available in specific namespaces by defining the following in inventory/group_vars/all/all.yml:
k8s_glusterfs_namespaces:
- default
- kube-system
By defining GlusterFS into specific namespaces allows persistent storage to be available for consumption within those namespaces.
You must first deploy the Kubernetes Endpoints
and Service
defined in
deployments/glusterfs.yaml. This file is dynamically
generated during provisioning if glusterfs_volume_force_create: true
.
kubectl apply -f deployments/glusterfs.yaml
In order to use GlusterFS
for persistent storage you must define your pod(s) to
do so. Below is an example of a pod definition:
---
apiVersion: v1
kind: Pod
metadata:
name: glusterfs
spec:
containers:
- name: glusterfs
image: armhfbuild/nginx
volumeMounts:
- mountPath: /mnt/glusterfs
name: glusterfsvol
volumes:
- name: glusterfsvol
glusterfs:
endpoints: glusterfs-cluster
path: volume-1
readOnly: false
We have included a few deployments to get some monitoring of your environment going as well. These include Heapster, InfluxDB, and Grafana.
In order to get cluster metrics into InfluxDB and Grafana we must first deploy Heapster. Heapster enables container monitoring and performance analysis for Kubernetes. To deploy Heapster simply run the following:
kubectl apply -f deployments/heapster.yaml
...
clusterrolebinding "heapster" created
serviceaccount "heapster" created
deployment "heapster" created
service "heapster" created
After deploying Heapster we are now ready to deploy InfluxDB and Grafana.
NOTE: The current deployment of InfluxDB/Grafana depends on GlusterFS being deployed. So if that has not been deployed yet you will either need to or adjust the
influx-grafana.yaml
deployment to adjust for the volumes. Also Traefik for load balancing is required to properly connect to Grafana's WebUI.
kubectl apply -f deployments/influx-grafana.yaml
...
deployment "monitoring-grafana" created
service "monitoring-grafana" created
deployment "monitoring-influxdb" created
service "monitoring-influxdb" created
ingress "monitoring-grafana" created
After the deployment above has been successful you should be able to connect to
the Grafana WebUI at http://wirelessIP/grafana
.
And from the screenshot above you will notice that two dashboards
(cluster
and pods
) are already pre-loaded during deployment.
If for any reason you would like to reset the Kubernetes cluster. You can easily
run the following Ansible
playbook which will take care of that for you.
ansible-playbook -i inventory/ playbooks/reset_cluster.yml
MIT
Larry Smith Jr.