See output of my flash below. Note: Putty remains blank when trying to remote into this device directly over USB.
Not sure if the flash was successful or not. It appears so, but unable to get a successful connection with Putty.
#########################################
# Marauder Flasher Script v1.90 #
# By Frog, tweaked by UberGuidoZ #
# and by ImprovingRigmarole #
#########################################
esptool.py v4.1
Serial port COM4
Connecting.....
Chip is ESP32-S2
Features: WiFi, No Embedded Flash, No Embedded PSRAM, ADC and temperature sensor calibration in BLK2 of efuse V2
Crystal is 40MHz
MAC: 68:67:25:c0:c6:ba
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 921600
Changed.
Erasing region (may be slow depending on size)...
Erase completed successfully in 0.4 seconds.
Staying in bootloader.
Traceback (most recent call last):
File "esptool.py", line 34, in <module>
File "esptool\__init__.py", line 995, in _main
File "esptool\__init__.py", line 820, in main
File "esptool\loader.py", line 1334, in soft_reset
File "esptool\loader.py", line 806, in flash_finish
File "esptool\loader.py", line 378, in check_command
File "esptool\loader.py", line 365, in command
File "serial\serialutil.py", line 372, in timeout
File "serial\serialwin32.py", line 222, in _reconfigure_port
serial.serialutil.SerialException: Cannot configure port, something went wrong. Original message: OSError(22, 'A device which does not exist was specified.', None, 433)
[16860] Failed to execute script 'esptool' due to unhandled exception!
Firmware Erased, preparing write...
esptool.py v4.1
Serial port COM4
Connecting.....
Chip is ESP32-S2
Features: WiFi, No Embedded Flash, No Embedded PSRAM, ADC and temperature sensor calibration in BLK2 of efuse V2
Crystal is 40MHz
MAC: 68:67:25:c0:c6:ba
Uploading stub...
Running stub...
Stub running...
Changing baud rate to 921600
Changed.
Configuring flash size...
Flash will be erased from 0x00001000 to 0x00004fff...
Flash will be erased from 0x00008000 to 0x00008fff...
Flash will be erased from 0x00010000 to 0x000e0fff...
Compressed 13648 bytes to 9382...
Wrote 13648 bytes (9382 compressed) at 0x00001000 in 0.4 seconds (effective 256.6 kbit/s)...
Hash of data verified.
Compressed 3072 bytes to 129...
Wrote 3072 bytes (129 compressed) at 0x00008000 in 0.1 seconds (effective 225.5 kbit/s)...
Hash of data verified.
Compressed 854752 bytes to 564103...
Wrote 854752 bytes (564103 compressed) at 0x00010000 in 17.3 seconds (effective 396.2 kbit/s)...
Hash of data verified.
Leaving...
Staying in bootloader.
Traceback (most recent call last):
File "esptool.py", line 34, in <module>
File "esptool\__init__.py", line 995, in _main
File "esptool\__init__.py", line 820, in main
File "esptool\loader.py", line 1334, in soft_reset
File "esptool\loader.py", line 806, in flash_finish
File "esptool\loader.py", line 378, in check_command
File "esptool\loader.py", line 365, in command
File "serial\serialutil.py", line 372, in timeout
File "serial\serialwin32.py", line 222, in _reconfigure_port
serial.serialutil.SerialException: Cannot configure port, something went wrong. Original message: OSError(22, 'A device which does not exist was specified.', None, 433)
[22884] Failed to execute script 'esptool' due to unhandled exception!
-----------------------------------------------------------------------------------------------
Process has completed Please disconnect your Wifi Devboard and connect it to your Flipper Zero.
==========================================================================
ERRORS ABOVE MAY BE NORMAL - Please ignore them for now and give it a try.
==========================================================================
(You may now close this window or press any key to exit.)