Hall C single arm Monte Carlo for HMS and SHMS

To compile type "make" in the src directory. NOTE: Make sure paths to Cern libararies are defined. On JLab machines, do "setup cernlib/2005".

Main code is mc_single_arm.f

If include files are changed it is best to do "make Clean" and then "make" since the Makefile is not smart enough to look for dependency

Easiest way is to use "run_mc_single_arm "

Alternately: cd src mc_single_arm (ask for input file name (assumed in infiles subdirectory))

• Input file : infile_name.inp
• Output file is at outfiles/infile_name.out
• The hbook file is at worksim/infile_name.rzdat
• Hard coded flags in mc_single_arm.f ** hut_ntuple : Write out ntuple (1 for HMS and 1411 for SHMS) described below. (true) ** spec_ntuple: Write out ntuple 1412 described below (false) ** decay_flag : Allow decay of particle(false)
• Hard coded flags in shms/mc_shms.f ** use_coll : pass particles through the collimator between HB and Q1 (true)

• Read in the input file
• Starts event loop
• The seed for the random number generator is picked by the time. each run of the code will be different set of random numbers.
• The lab or beam coordinate system has +z along the target towards the beam dump, +y is vertical pointing down and +x is pointing beam left.
• Randomly selects beam-target interaction point.
• The coordinate system of the SHMS is +z_s along the central ray, +x_s is vertical pointing down and +y_s is horizontal point to large angle.
• Randomly selects particle delta=(p-pcent)/p, dy_s/dz_s amd dx_s/dz_s.
• Drifts to z_s=0 plane
• Calculated multiple scattering the target using the input radiation length ** If target length greater than 3cm assume LH2 cryotarget for multiple scattering calculation. ** If target length less than 3cm assume simple solid target for multiple scattering calculation.
• calulated mutliple scattering in scattering chamber window, air and spectrometer entrance window.
• Call the mc_shms/mc_hms subroutine to transport the particle through SHMS/HMS apertures and to the focal plane.
• At the focal plane drift the particle through 1st Cerenkov or vacuum pipe (for SHMS only, depending on flag in input file),the drift chamber, scintillators, 2nd cerenkov and calorimeter to check if it hits them .
• As it passes through the drift chamber randomly change the position according to the presumed DC resolution and fit the positions and calculate the focal plane positions and angles.
• From focal plane calculate the reconstructed target quantities ytar,yptar,xptar and delta using the optics matrix. Note that for now use the known x target position in the optics matrix calculations. To mimic what would be in the analysis, need to calculate xtar from the reconstructed quantities using the raster vertical position and then recalculate the reconstructed quantities with updated xtar.
• If particle makes it to the focal plane and hits all detectors the event variables are put in ntuple.

• hms: HMS subroutines
• shms : SHMS subroutines
• infiles : input files
• outfiles : the output files
• worksim : rzdat files

• Mostly self explanatory
• dp/p down and up should be at least -15.0 and 25.0
• theta down and up is dy/dz , horizontal angle relative to central ray keep at least -55,55mr
• phi down and up is the dx/dz, vertical angle relative to central ray ,keep at least -50, 50mr
• Remember to keep the Dp/p,theta,phi and ztgt reconstruction cut larger than thrown.
• The target length just need to set flag if aerogel will be in the detector stack
• Up to the experiment to decide if the 1st Cerenkov detector will be needed for the experiemnt
• If 1st Cerenkov not used then can replace with vacuum pipe. Option of helium bag is availble. this was for study.
• The multifoil optics targets can be implementented by entering the target length as -2 for the optics2 target (two foils) and -3 for optics1 target (three foils).
• the sieve can be used by setting the flag == 1. (See infiles/ examples)

• psxfp Focal plane vertical position
• psyfp Focal plane horizontal position
• psxpfp Focal plane vertical angle=dx/dz
• psypfp Focal plane horizontal angle=dy/dz
• psztari Initial random position along the target
• psytari Initial y (horizontal) position at the z=0 plane perpendicular to central ray of SHMS
• psdeltai Initial random delta = (p-pcent)/pcent
• psyptari Initial random horizontal angle=dy/dz
• psxptari Initial random vertical angle=dx/dz
• psztar Reconstructed position along the target
• psytar Reconstructed
• psdelta Reconstructed
• psyptar Reconstructed
• psxptar Reconstructed
• psxtari Initial x (vertical) position at the z=0 plane perpendicular to central ray of SHMS
• fry Initial random vertical raster position
• xsnum sieve slit vertical hole number ( hole number at front sieve if use_front_sieve = true)
• ysnum sieve slit horizontal hole number ( hole number at front sieve if use_front_sieve = true)
• xsieve sieve slit vertical position (cm) ( position at front sieve if use_front_sieve = true)
• ysieve sieve slit horizontal position (cm) ( position at front sieve if use_front_sieve = true)
• stop_id information on where the track ended (0=successful reached detectors)
• psvxi initial x position in the beam following system
• psvyi initial y position in the beam following system

• same as SHMS except the variables start with "hs" instead of "ps". e.g. psdelta ---> hsdelta