[BUG] Setting EXTRUDERS 0 fails to compile about marlin HOT 3 CLOSED

diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 72ec272b4d..4cebaab7ca 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -68,7 +68,7 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_BTT_OCTOPUS_V1_1
 #endif
 
 /**
@@ -79,7 +79,7 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT 0
+#define SERIAL_PORT -1
 
 /**
  * Serial Port Baud Rate
@@ -139,9 +139,9 @@
  *          TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#define X_DRIVER_TYPE  A4988
-#define Y_DRIVER_TYPE  A4988
-#define Z_DRIVER_TYPE  A4988
+#define X_DRIVER_TYPE  TMC2209
+#define Y_DRIVER_TYPE  TMC2209
+#define Z_DRIVER_TYPE  TMC2209
 //#define X2_DRIVER_TYPE A4988
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
@@ -153,7 +153,7 @@
 //#define U_DRIVER_TYPE  A4988
 //#define V_DRIVER_TYPE  A4988
 //#define W_DRIVER_TYPE  A4988
-#define E0_DRIVER_TYPE A4988
+//#define E0_DRIVER_TYPE A4988
 //#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
@@ -208,7 +208,7 @@
 
 // This defines the number of extruders
 // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
-#define EXTRUDERS 1
+#define EXTRUDERS 0
 
 // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
 #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
@@ -553,7 +553,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 0
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -1236,7 +1236,7 @@
  * Override with M92 (when enabled below)
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400 }
 
 /**
  * Enable support for M92. Disable to save at least ~530 bytes of flash.
@@ -1248,11 +1248,11 @@
  * Override with M203
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
-  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -1261,11 +1261,11 @@
  * Override with M201
  *                                      X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
-  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -1305,7 +1305,7 @@
 
   //#define LIMITED_JERK_EDITING        // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
   #if ENABLED(LIMITED_JERK_EDITING)
-    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
+    #define MAX_JERK_EDIT_VALUES { 20, 20, 0.6 } // ...or, set your own edit limits
   #endif
 #endif
 
@@ -1718,7 +1718,7 @@
 #define X_ENABLE_ON 0
 #define Y_ENABLE_ON 0
 #define Z_ENABLE_ON 0
-#define E_ENABLE_ON 0 // For all extruders
+//#define E_ENABLE_ON 0 // For all extruders
 //#define I_ENABLE_ON 0
 //#define J_ENABLE_ON 0
 //#define K_ENABLE_ON 0
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index f0066338c1..0f2ae478e8 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1218,7 +1218,7 @@
 
 // @section motion
 
-#define AXIS_RELATIVE_MODES { false, false, false, false }
+#define AXIS_RELATIVE_MODES { false, false, false }
 
 // Add a Duplicate option for well-separated conjoined nozzles
 //#define MULTI_NOZZLE_DUPLICATION
@@ -3337,7 +3337,7 @@
    * M912 - Clear stepper driver overtemperature pre-warn condition flag.
    * M122 - Report driver parameters (Requires TMC_DEBUG)
    */
-  //#define MONITOR_DRIVER_STATUS
+  #define MONITOR_DRIVER_STATUS
 
   #if ENABLED(MONITOR_DRIVER_STATUS)
     #define CURRENT_STEP_DOWN     50  // [mA]
@@ -3405,23 +3405,23 @@
    * Comment *_STALL_SENSITIVITY to disable sensorless homing for that axis.
    * @section tmc/stallguard
    */
-  //#define SENSORLESS_HOMING // StallGuard capable drivers only
+  #define SENSORLESS_HOMING // StallGuard capable drivers only
 
   #if ANY(SENSORLESS_HOMING, SENSORLESS_PROBING)
     // TMC2209: 0...255. TMC2130: -64...63
-    #define X_STALL_SENSITIVITY  8
-    #define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
-    #define Y_STALL_SENSITIVITY  8
-    #define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
-    //#define Z_STALL_SENSITIVITY  8
+    #define X_STALL_SENSITIVITY  120
+    //#define X2_STALL_SENSITIVITY X_STALL_SENSITIVITY
+    #define Y_STALL_SENSITIVITY  120
+    //#define Y2_STALL_SENSITIVITY Y_STALL_SENSITIVITY
+    #define Z_STALL_SENSITIVITY  120
     //#define Z2_STALL_SENSITIVITY Z_STALL_SENSITIVITY
     //#define Z3_STALL_SENSITIVITY Z_STALL_SENSITIVITY
     //#define Z4_STALL_SENSITIVITY Z_STALL_SENSITIVITY
-    //#define I_STALL_SENSITIVITY  8
-    //#define J_STALL_SENSITIVITY  8
-    //#define K_STALL_SENSITIVITY  8
-    //#define U_STALL_SENSITIVITY  8
-    //#define V_STALL_SENSITIVITY  8
+    #define I_STALL_SENSITIVITY  120
+    #define J_STALL_SENSITIVITY  120
+    #define K_STALL_SENSITIVITY  120
+    #define U_STALL_SENSITIVITY  120
+    #define V_STALL_SENSITIVITY  120
     //#define W_STALL_SENSITIVITY  8
     //#define SPI_ENDSTOPS              // TMC2130/TMC5160 only
     //#define IMPROVE_HOMING_RELIABILITY
@@ -3450,7 +3450,7 @@
    * Enable M122 debugging command for TMC stepper drivers.
    * M122 S0/1 will enable continuous reporting.
    */
-  //#define TMC_DEBUG
+  #define TMC_DEBUG
 
   /**
    * You can set your own advanced settings by filling in predefined functions.