docker run -d --name='PhoenixMiner' --net='bridge' -e TZ="Australia/Sydney" --device='/dev/dri:/dev/dri' 'lnxd/phoenixminer' ./PhoenixMiner -pool asia1.ethermine.org:4444 -wal 0xe037C6245910EbBbA720514835d31B385D76927f.x

Phoenix Miner 5.6d Linux/gcc - Release build
--------------------------------------------

Usage: PhonixMiner [OPTIONS]
Options:

Pool options (normal mode):
  -pool <host:port> Ethash pool address
  -wal <wallet> Ethash wallet (some pools want user name and/or worker)
  -pass <password> Ethash password (most pools don't require it)
  -worker <name> Ethash worker name (most pools accept it as part of wallet)
  -proto <n> Selects the kind of stratum protocol for the ethash pool:
     1: miner-proxy stratum spec (e.g. coinotron)
     2: eth-proxy (e.g. ethermine, nanopool) - this is the default
     3: qtminer (e.g. ethpool)
     4: EthereumStratum/1.0.0 (e.g. nicehash)
     5: EthereumStratum/2.0.0
  -coin <coin> Ethash coin to use for devfee to avoid switching DAGs:
     auto: Try to determine from the pool address (default)
     eth: Ethereum
     etc: Ethereum Classic
     exp: Expanse
     music: Musicoin
     ubq: UBIQ
     pirl: Pirl
     etp: Metaverse ETP
     ella: Ellaism
     whale: WhaleCoin
     vic: Victorium
     nuko: Nekonium
     mix: MIX
     egem: EtherGem
     clo: Callisto
     dbix: DubaiCoin
     moac: MOAC
     etho: Ether-1
     yoc: Yocoin
     b2g: Bitcoiin2Gen
     esn: Ethersocial
     ath: Atheios
     reosc: REOSC
     qkc: QuarkChain
     bci: Bitcoin Interest
  -stales <n> Submit stales to ethash pool: 1 - yes (default), 0 - no
  -pool2 <host:port>  Failover ethash pool address
  -wal2 <wallet> Failover ethash wallet (if missing -wal will be used)
  -pass2 <password> Failover ethash password (if missing -pass will be used)
  -worker2 <name> Failover ethash worker name (if missing -worker will be used)
  -proto2 <n> Failover ethash stratum protocol (if missing -proto will be used)
  -coin2 <coin> Failover devfee Ethash coin (if missing -coin will be used)
  -stales2 <n> Submit stales to the failover pool: 1 - yes (default), 0 - no
  -dpool <host:port>  Dual mining pool address
  -dwal <wallet> Dual mining wallet
  -dpass <password> Dual mining pool password
  -dworker <name> Dual mining worker name
  -dcoin blake2s Dual mining algorithm (currently only blake2s)
  -dstales <n> Submit stales to dual mining pool: 1 - yes (default), 0 - no
General pool options:
  -fret <n> Switch to next pool afer N retries (default: 3)
  -ftimeout <n> Reconnect if no new ethash job is receved for n seconds
    (default: 600)
  -ptimeout <n> Switch back to primary pool after n minutes (30 by default;
    set to 0 to disable automatic switch back to primary pool)
  -retrydelay <n> Seconds before reconnecting (default: 5)
  -gwtime <n> Recheck period for Solo/GetWork mining (default: 200 ms)
  -rate <n> Report hashrate to the pool: 1 - yes, 0 - no (1 is the default)
Benchmark mode:
  -bench [<n>],-benchmark [<n>] Benchmark mode, optionally specify DAG epoch
Remote control options:
  -cdm <n> Selects the level of support of the CDM remote monitoring:
     0: disabled
     1: read-only - this is the default
     2: full (only use on secure connections)
  -cdmport <port> Set the CDM remote monitoring port or <ip_addr:port>
    (default 3333)
  -cdmpass <pass> Set the CDM remote monitoring password
  -cdmrs Reload the settings if config.txt is edited/uploaded remotely
Mining options:
  -amd  Use only AMD cards
  -acm  Turn on AMD compute mode (requires administrative rights)
  -nvidia  Use only Nvidia cards
  -gpus <123 ..n> Use only the specified GPUs (if more than 10, separate
    the indexes with comma)
  -mi <n> Set the mining intensity (0 to 14; 12 is the default)
  -gt <n> Set the GPU tuning parameter (6 to 400). The default is 15
  -sci <n> Dual mining intensity (1 to 1000). The default is 30
  -mode <n> Mining mode (0: dual mining; 1: ethash only). Use this option
            if you want only some of the GPUs to dual mine
  -clKernel <n> Type of AMD kernel: 0 generic, 1 optimized, 2 alterantive
    (1 is the default, 2 is only for RX470/570/480/580)
  -clGreen <n> Use power-efficient AMD kernels (0: no, 1: yes; default: 0)
  -clNew <n> Use new AMD kernels if supported (0: no, 1: yes; default: 1)
  -clf <n> AMD kernel sync (0: never, 1: periodic; 2: always; default: 1)
  -nvKernel <n> Type of Nvidia kernel: 0 - auto (the default),
    1 oldest (v1), 2 - newer (v2, since PM4.0), 3 - latest (v3)
  -nvdo <n> Use Nvidia driver-specific optimizations (0: no; default, 1: yes)
  -nvNew <n> Use new Nvidia kernels if supported (0: no, 1: yes; default: 1)
  -nvf <n> Nvidia kernel sync (0-3; default: 1)
  -list List the detected GPUs devices and exit
  -gbase <n> Set the index of the first GPU (0 or 1, default: 1)
  -minRigSpeed <n> Restart the miner if avg 5 min speed is below <n> MH/s
  -eres <n> Allocate DAG buffers big enough for n epochs ahead (default: 2)
  -dagrestart <n> Restart the miner when allocating buffer for new DAG epoch:
     0 - never, 1 - always, 2 - auto (default)
  -daglim <n> DAG size limit (0 - off, 1 - auto, >1000 - DAG size limit in MB)
  -lidag <n> Slow down DAG generation to avoid crash (0-3, default: 0 - fastest)
  -gser <n> Stagger DAG generation to avoid crash (0: no, 1: minimal; 2: full)
  -gpureset <n> Fully reset GPU when paused (0 - no, 1 - yes; default: 0)
  -rvram <n> Minimum free VRAM (-1: don't check; default: 128)
  -altinit Use alternative way to initialize AMD cards to prevent startup crashes
  -gpow <n> Lower the GPU usage to n% of maximum (default: 100)
  -wdog <n> Enable watchdog timer: 1 - yes, 0 - no (1 is the default)
  -wdtimeout <n> Watchdog timeout (30 - 300; default 45 seconds)
  -gswin <n> GPU stats time window (5-30 sec; default: 15; use 0 to
    revert to pre-2.8 way of showing momentary stats)
  -gsi <n> Speed stats interval (5-30 sec; default: 5; user 0 to disable)
  -astats <n> Show advanced stats from Web sources (0: no; 1: yes)
  -rmode <n> Selects the restart mode:
     0: disabled - miner will shut down instead of restarting
     1: restart with the same cmdline options - this is the default
     2: reboot (shut down miner and execute reboot.bat)
  -log <n> Selects the log file mode:
     0: disabled - no log file will be written
     1: write log file but don't show debug messages on screen
     2: write log file and show debug messages on screen
  -logfile <name> Set the name of the log file
  -logdir <path> Set a directory for the log file(s)
  -logsmaxsize <n> Max size of old log files in MB (default: 200)
  -timeout <n> Restart miner according to -rmode after n minutes
  -pauseat hh:mm Pause the miner at hh::mm (24 hours time)
  -resumeat hh::mm Resume the miner at hh::mm (24 hours time)
Hardware control options:
  -hwm <n> Hardware monitoring frequency (the default is 1):
      0 - no HW monitoring on all cards, 1 - normal monitoring,
      2 to 5 - less frequent monitoring
  -tt <n> Set fan control target temperature (special values:
      0 - no fan control, negative - fixed fan speed at n%)
  -ttj <n> Set fan control target junction temperature (can be used
      only on GPUs that report the junction temperature)
  -ttmem <n> Set fan control target video memory temperature (can be used
      only on GPUs that report the VRAM temperature)
  -fanmin <n> Set fan control min speed in % (-1 for default)
  -fanmax <n> Set fan control max speed in % (-1 for default)
  -fanstop <n> If disabled (0, the default) the miner will not allow the fans
      to stop if fixed fan speed (e.g. -tt -40), or -fanmin is used
  -fcm <n> Set fan control mode (0 - auto, 1 - normal, 2 - alt; default: 0)
  -fpwm <n> Fan PWM mode (0 - auto, 1 - direct, 2 - Polaris,
      3 - Vega, 4 - Radeon VII, Navi; default: 0)
  -fanidle <n> Set idle fan speed in % (-1 is auto, the default is 20)
  -tmax <n> Set fan control max temperature (0 for default)
  -powlim <n> Set GPU power limit in % (from -75 to 75, 0 for default)
  -cclock <n> Set GPU core clock in MHz (0 for default)
  -cvddc <n> Set GPU core voltage in mV (0 for default)
  -mclock <n> Set GPU memory clock in MHz (0 for default)
  -mvddc <n> Set GPU memory voltage in mV (0 for default)
  -straps <n> Memory strap level (0 - default)
  -vmt1 <n> Memory timing parameter 1 (0 to 100, default 0)
  -vmt2 <n> Memory timing parameter 2 (0 to 100, default 0)
  -vmt3 <n> Memory timing parameter 3 (0 to 100, default 0)
  -vmr <n> Memory refresh rate (0 to 100, default 0)
  -nvmem <n> Force using straps on unsupported Nvidia GPUs (0 - auto,
      1 - GDDR5, 2 - GDDR5X)
  -vmdag <n> Reset straps during DAG generation (default: 1)
  -mcdag <n> Reset mem clocks during DAG generation (default: 0; Nvidia only)
  -mt <n> Memory timing level (0 - VBIOS/default), AMD only
  -leavemt Do not reset memory timing level to 0 when closing
  -ttli <n> Lower GPU usage when temp is >= n deg C (0 for default)
  -tmaxj <n> Lower GPU usage when junction temp is >= n deg C (0 for default;
      can be used only on GPUs that report the junction temperature)
  -tmaxmem <n> Lower GPU usage when VRAM temp is >= n deg C (0 for default;
      can be used only on GPUs that report the VRAM temperature)
  -hstats <n> HW stats mode (0: temp and fan speed only,
    1: temp, fan speed and power, 2: full; default: 1)
  -pidle <n> Idle power usage in W (will be added to GPU power)
  -prate <n> Power price in USD per kWh  -ppf <n> Power correction for GPU power usage in %.
    E.g. -ppf 105 means that reported GPU power will be multiplied by 1.05
  -tstop <n> Pause GPU when temp is >= n deg C (0 for default)
  -tstart <n> Resume GPU when temp is <= n deg C (0 for default)
  -resetoc Reset the overclocking settings on startup
  -leaveoc Do not reset overclocking setings when closing
  -config <filename> Load file with configuration options
  -openclLocalWork <n> Set the OpenCL local work size (advanced)
  -openclGlobalMultiplier <n> Set the OpenCL global work size (advanced; will
    be multiplied by the number of computing units)
  -cudaBlockSize <n> Set the CUDA block size (advanced)
  -cudaGridMultiplier <n> Set the CUDA grid size (advanced; will be multiplied
    by the number of computing units)
General Options:
  -v,-version  Show the version and exit
  -h,-help  Show this help message and exit