isaac96 / unojoy Goto Github PK
View Code? Open in Web Editor NEWAutomatically exported from code.google.com/p/unojoy
Automatically exported from code.google.com/p/unojoy
What steps will reproduce the problem?
1. run the LeoJoy installer for windows
2. open the arduino program
3. Load LeoJoy from emaples and upload
What is the expected output? What do you see instead?
LeoJoy:84: error: 'dataForController_t' does not name a type
LeoJoy.ino: In function 'void loop()':
LeoJoy:86: error: 'dataForController_t' was not declared in this scope
LeoJoy:86: error: expected `;' before 'controllerData'
LeoJoy:89: error: 'Joystick' was not declared in this scope
LeoJoy:89: error: 'controllerData' was not declared in this scope
LeoJoy.ino: At global scope:
LeoJoy:108: error: 'dataForController_t' does not name a type
What version of the product are you using? On what operating system?
Windows 7
Please provide any additional information below.
Original issue reported on code.google.com by [email protected]
on 14 Sep 2013 at 10:39
What steps will reproduce the problem?
1.trying to test
2.
3.
What is the expected output? What do you see instead?
i try to test the arduino with using the pin 2 key to ground and it does
nothing just shows up as another button is pressed all the time and should pin
13 light be on all the while
What version of the product are you using? On what operating system?
wins 7 64gb
Please provide any additional information below.
Original issue reported on code.google.com by [email protected]
on 15 Mar 2015 at 1:55
I have an Arduino Duemilanove and a Arduino Nano. Are any of this IC compatible
with this bootloader? If so then can someone show me the steps for burning the
bootloader on those chips? I saw somewhere in the code that there is an
exception for Duemilanove but I don't understand.
Original issue reported on code.google.com by [email protected]
on 26 Aug 2013 at 1:57
On an Arduino uno REV3
Can't turn back into arduino mode when executing batch file "turninot
arduino.bat"
How can I reset to arduino mode ?
Original issue reported on code.google.com by [email protected]
on 29 May 2014 at 12:55
What steps will reproduce the problem?
1. trying to install lionunojoy driver
2. also then turnintojoystick.command doesn't work, as it says I don't have
permission
3.
What is the expected output? What do you see instead?
Installation to happen. I see this message: An error occurred while running the
InstallationCheck tool for “LionUnoJoyDrivers”. Try running the tool again.
What version of the product are you using? On what operating system?
I'm using lion 10.7.5 on a mac and a freeduino v1.22
Please provide any additional information below.
That's about it
Original issue reported on code.google.com by [email protected]
on 26 Feb 2013 at 5:43
What steps will reproduce the problem?
1.Load UnoJoyArduinoSample code into UNO R3
2.Open UnoJoyProcessingVisualizer.exe
3.Window open,but only with gray screen, and it is stuck there
What is the expected output? What do you see instead?
Window open,but only with gray screen, and it is stuck there
What version of the product are you using? On what operating system?
Win XP SP3
UnoJoyWin-21Feb2013
Please provide any additional information below.
Loaded drivers, but just can't get it to work, Updated Java
Original issue reported on code.google.com by [email protected]
on 9 Apr 2014 at 1:46
What steps will reproduce the problem?
1.Running atmel flip
2.Got latest version of java RTE
3.Atmel flip does not start: "an error with error code 2 occurred" on startup,
won't go further after this
What is the expected output? What do you see instead?
running atmel flip...
What version of the product are you using? On what operating system?
3.4.7 on windows 8.1
Please provide any additional information below.
Original issue reported on code.google.com by [email protected]
on 11 Jan 2015 at 5:36
This started happening after installing the drivers to get UnoJoy and MegaJoy
running on my Windows 7 64-bit machine.
Looking at Devices and Printers, and hearing the Windows notification tones, an
Unknown Device appears for a second like it is a new hardware device or was
just connected, then it is removed from Devices and Printers after about a
second or two, with the Windows notification tone. It happens at random
intervals every 2 to 10 seconds.
Whether the Arduino card is plugged in or not does not make a difference.
Original issue reported on code.google.com by [email protected]
on 9 Apr 2014 at 5:28
What is the expected output? What do you see instead?
I want to make a button box for iRacing but i dont know how to connect thw
switches and when i connect ground and a digital input the arduino make a
reset. And when i go to see the Unojoy in the device manager all the buttons
are flashing all the time.
What version of the product are you using? On what operating system?
MegaJoy in Arduino Mega256016u2 W8.1 x64
Thanks in advance
Original issue reported on code.google.com by [email protected]
on 6 Feb 2015 at 7:59
What steps will reproduce the problem?
1. Trying to open the driver
2. My Mac is version: 10.8, and it comes back with an error saying it's for v.
10.7
What is the expected output? What do you see instead?
Installation.
Refuses to install: "this was compiled for Mac OSX 10.7"
What version of the product are you using? On what operating system?
UnoJoyOSX-21Feb2013
OSX 10.8.3
Please provide any additional information below.
Looking forward to trying it out.
Original issue reported on code.google.com by [email protected]
on 18 Apr 2013 at 3:35
I followed all the steps and ran the windows batch file. My output was this:
Abracadabra!
C:\Users\adam\Downloads\UnoJoyWin-15May2012\UnoJoyWin\ATmega8u2Code\HexFiles>bat
chisp -device at90usb82 -hardware usb -operation erase f memory flash blankcheck
loadbuffer "UnoJoy.hex" program verify start reset 1024
Running batchisp 1.2.5 on Mon Oct 15 17:26:20 2012
AT90USB82 - USB - USB/DFU
Device selection....................... PASS
Hardware selection..................... PASS
Opening port........................... AtLibUsbDfu: 3EB 2FF7 no device present.
FAIL Could not open USB device.
ISP done.
-1
The firmware was NOT loaded...
Did you install the Atmel FLIP program? - http://www.atmel.com/tools/FLIP.aspx -
Is the Arduino plugged in?
Is is it in 'Arduino UNO DFU' mode?
Press any key to exit..
The arduino is plugged in and in DFU mode although it shows as the ATmega16U2
not the arduino DFU mode under system devices. Any solutions?
Original issue reported on code.google.com by [email protected]
on 15 Oct 2012 at 11:37
Any chances of adding force feedback.?
I've been battling through HID descriptors for days now.
Original issue reported on code.google.com by [email protected]
on 30 Jun 2014 at 7:38
On my computer COM3 is occupied by "Dell Wireless 5530 HSPA Mini-Card Device
Management".
When starting UnoJoyProcessingVisualizer.exe nothing seem to happen. No window
opens. But there is a java process visible in the Task Manager.
Starting UnoJoyProcessingVisualizer from the command line gives the following
output:
>"C:\Program Files (x86)\Java\jdk1.6.0_20\bin\java" -classpath
lib\core.jar;lib\RXTXcomm.jar;lib\serial.jar;lib\UnoJoyProcessingVisualizer.jar
UnoJoyProcessingVisualizer
WARNING: RXTX Version mismatch
Jar version = RXTX-2.2pre1
native lib Version = RXTX-2.2pre2
COM3
Error 0x5 at ..\src\termios.c(892): Zugriff verweigert
gnu.io.PortInUseException: Unknown Application
at gnu.io.CommPortIdentifier.open(CommPortIdentifier.java:467)
at processing.serial.Serial.<init>(Unknown Source)
at processing.serial.Serial.<init>(Unknown Source)
at UnoJoyProcessingVisualizer.setup(UnoJoyProcessingVisualizer.java:104)
at processing.core.PApplet.handleDraw(Unknown Source)
at processing.core.PApplet.run(Unknown Source)
at java.lang.Thread.run(Thread.java:619)
Exception in thread "Animation Thread" java.lang.RuntimeException: Error inside
Serial.<init>()
at processing.serial.Serial.errorMessage(Unknown Source)
at processing.serial.Serial.<init>(Unknown Source)
at processing.serial.Serial.<init>(Unknown Source)
at UnoJoyProcessingVisualizer.setup(UnoJoyProcessingVisualizer.java:104)
at processing.core.PApplet.handleDraw(Unknown Source)
at processing.core.PApplet.run(Unknown Source)
at java.lang.Thread.run(Thread.java:619)
Disabling the devices which occupy COM3 and COM4 ports and restarting the
computer will make UnoJoyProcessingVisualizer pick COM4. But my Arduino is on
COM7. Manually reassigning Arduino to COM4 finally will lead to success. But
usually COM4 is already used by a driver in my system which com port assignment
I cannot change.
> What is the expected output?
A window should show the exception instead of just doing nothing.
I don't know if it is possible to fix com port discovery. But in every case
it'd be a good step to allow the user to select the com port.
Original issue reported on code.google.com by [email protected]
on 9 Jan 2013 at 7:46
What steps will reproduce the problem?
1. run the UnoJoyProcessingVisualizer sketch
2.
3.
What is the expected output? What do you see instead?
i see nothing !
What version of the product are you using? On what operating system?
proccessing 2.0b7
Please provide any additional information below.
dude what the F
Original issue reported on code.google.com by [email protected]
on 21 Feb 2013 at 8:19
Attachments:
Hi there,
would it possible to implement a pass-through mode for making the MegaJoy /
UnoJoy work with the Xbox360? There is a similar, open-source project. Maybe it
would be possible to reuse some lines:
https://github.com/IvIePhisto/Dual-Strike.
Thank you!
Original issue reported on code.google.com by [email protected]
on 23 Jan 2014 at 2:39
What the problem?
In your soft, windows find right stick X and Y is the Z axes,
I prefer he recognise right stick X and Y as axe X and Y.
Please tell me how change this. My project is a mamecab, with a frontend
atomicfe (he doesn't recognize D_pad in menu only axe) i don't use Z axes, I
use only 6 buttons and X Y axes.
What version of the product are you using? On what operating system?
I use 24may2012 version on windows 7 64 bits.
Please provide any additional information below.
Sorry for my english, i'm a french users, otherwise great job.
Original issue reported on code.google.com by [email protected]
on 27 Jul 2012 at 11:33
Just tried Unojoy out for the first time and found that the .command files to
reflash the Arduino using OS X are actually the same as on the Windows .bat
files. I worked around this using the .command files from an older release.
Original issue reported on code.google.com by [email protected]
on 25 Apr 2013 at 12:58
Added the ifdef for f_cpu option to allow the code to recognize 8Mhz devices in
the boards.txt file.
Original issue reported on code.google.com by [email protected]
on 27 Jan 2014 at 9:38
Attachments:
I installed MegaJoy successfully(?) in Windows 7 64-bit and my Arduino Mega
2560 R3.
Windows sees the axis and buttons in both virtual joysticks as "UnoJoy
Joystick" (devices and printers).
To test the analog controller input, I put a potentiometer along the analog
input side of the Mega (A0 to A15).
In A0, Windows (Game Controllers -> UnoJoy properties) shows the x-axis /
y-axis (the open box) scroll across the top left/right as I move the
potentiometer.
A1 to A5 does nothing.
When I connect the potentiometer to A6 to A15 and setup virtual joystick 2
properties, all axis (plural) move as I turn the pot. So, the x/y axis box
moves diagonal top-left to bottom-right, the z-axis, x- and y- and z- rotation
bars move from left to right at one time.
What I would like to do is use A1 as one axis (let's say x-rotation), A2 as
another axis (y-rotation)...etc. To be able to isolate the potentiometer for
one axis or rotation.
Original issue reported on code.google.com by [email protected]
on 9 Apr 2014 at 2:31
When we use the latest Arduino Uno R3 board which contains an ATmega16U2,
the dfu-programmer says: "no device present".
Maybe the dfu-programmer is flashing the wrong IC, the at90usb82
I am using the latest UnoJoyOSX file on my MacOSX Lion 10.7.3
Original issue reported on code.google.com by [email protected]
on 15 May 2012 at 11:46
Attachments:
Windows can use the joy stick and all inputs. However it dont matter which
input (A2.,A3...) i use all of the axis will move.
I have tried grounding the unused axis, but the all axis read zero.
All button are working fine.
I am using unojoywin 24 may 2012
And windows 7 32bit
Realy sorry if i have missed something (hoping i have really).
Thank
Original issue reported on code.google.com by [email protected]
on 4 Oct 2012 at 10:35
[deleted issue]
I've got a first gen Uno, I was able to write to it without an issue. However,
now that it's in Joystick mode, I'm unable to get it to go back to DFU mode.
Jumping the two pins causes it to restart as expected, but it doesn't get
recognized by windows as being in DFU mode. TurnIntoArduino fails to find
anything that it can flash. Flip is installed.
Original issue reported on code.google.com by [email protected]
on 24 Jun 2014 at 4:04
[deleted issue]
1.All appears OK up to Visualiser as described
2.Shorting pins as shown seems to do nothing
3.Running "Turn into a joystick" gives the fault
AtLibUsbDFU.dll not found
Device manager (Ports)shows it still as Arduino Uno (comm 8)
My device is a "compatible" UNO R3 smd model
Running Windows 7 Professional 64 bit (SP1)
Flip installed
(I'm very new to this)
Hope you can help
Original issue reported on code.google.com by [email protected]
on 28 Aug 2014 at 4:51
What steps will reproduce the problem?
1. Download the latest UnoJoy release
2. Put your Arduino in DFU mode
3. Run TurnIntoAJoystick.command
I am on A Snow Leopard 10.6.8 . Downloaded the latest release and followed the
Getting Started Procedure. I have installed the drivers for SnowLeopard and put
my Arduino R3 in DFU mode. However the dfu programmer isn't working at all.
First, in the latest release the TurnIntoAJoystick.command is the same as the
window version and gives command not found errors.
I than downloaded an older release and the script gives this errors :
Trying to program for Arduino Uno R1/R2...
dyld: Library not loaded: /usr/local/lib/libusb-1.0.0.dylib
Referenced from: /Users/Tarhun/Downloads/UnoJoyOSX 2/ATmega8u2Code/HexFiles/./dfu-programmer
Reason: image not found
/Users/Tarhun/Downloads/UnoJoyOSX 2/TurnIntoAJoystick.command: line 29: 3133
Trace/BPT trap ./dfu-programmer at90usb82 flash UnoJoy.hex
We didn't find the R1/R2 model, checking for an R3...
dyld: Library not loaded: /usr/local/lib/libusb-1.0.0.dylib
Referenced from: /Users/Tarhun/Downloads/UnoJoyOSX 2/ATmega8u2Code/HexFiles/./dfu-programmer
Reason: image not found
/Users/Tarhun/Downloads/UnoJoyOSX 2/TurnIntoAJoystick.command: line 29: 3136
Trace/BPT trap ./dfu-programmer atmega16u2 flash UnoJoy.hex
dfu-programmer couldn't connect to the Arduino...
Did you put the Arduino into DFU mode?
Did you install the libusb driver?
logout
my /usr/local/lib/ folder shows
libusb-0.1.4.4.5.dylib libusb.la libusbpp.dylib
libusb-0.1.4.dylib libusbpp-0.1.4.4.5.dylib libusbpp.la
libusb.dylib libusbpp-0.1.4.dylib
Original issue reported on code.google.com by [email protected]
on 28 Aug 2013 at 12:22
A declarative, efficient, and flexible JavaScript library for building user interfaces.
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google ❤️ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.