kiibohdforce's Introduction
The Kiibohd Controller ---------------------- TODO, write some insightful/informative :P Please give authors credit for modules used if you use in a distributed product :D ---------------------- Dependencies ---------------------- Below listed are the Arch Linux pacman names, AUR packages may be required. These depend a bit on which targets you are trying to build, but the general one: - cmake (2.8 and higher) - Teensy Loader (http://pjrc.com/teensy/loader.html) AVR Specific (Teensy 1.0/++,2.0/++) (try to use something recent, suggested versions below) - avr-gcc (4.8.0) - avr-binutils (2.23.2) - avr-libc (1.8.0) ARM Specific (Teensy 3.0) (Sourcery CodeBench Lite for ARM EABI (http://www.mentor.com/embedded-software/sourcery-tools/sourcery-codebench/editions/lite-edition/) - arm-none-eabi - TODO? ---------------------- Selecting Architecture ---------------------- This is where you choose which architecture you want to build for. The options are: - Teensy 1.0 (Not tested) - Teensy 1.0++ (Not tested) - Teensy 2.0 - Teensy 2.0++ - Teensy 3.0 Open up CMakeLists.txt in your favourite text editor. You are looking for: ### Compiler Family # #| Specify the compiler family to use #| Currently only supports AVR and ARM #| "avr" # Teensy 1.0 #| "avr" # Teensy 2.0 #| "avr" # Teensy++ 1.0 #| "avr" # Teensy++ 2.0 #| "arm" # Teensy 3.0 set( COMPILER_FAMILY "avr" ) Just change the COMPILER_FAMILY variable to whatever you are trying to build for. NOTE: If you change this option, you will *may* to delete the build directory that is created in the Building sections below. ---------------------- Selecting Microcontroller ---------------------- Even if you selected the "avr" family of microcontroller architectures, you will still need to specify a target microcontroller (or once more ARM microcontrollers are supported). Open up avr.cmake (or arm.cmake) in your favourite text editor. You are looking for: ### # Atmel Defines and Linker Options # #| MCU Name #| You _MUST_ set this to match the board you are using #| type "make clean" after changing this, so all files will be rebuilt #| #| "at90usb162" # Teensy 1.0 #| "atmega32u4" # Teensy 2.0 #| "at90usb646" # Teensy++ 1.0 #| "at90usb1286" # Teensy++ 2.0 set( MCU "at90usb1286" ) *OR* ### # ARM Defines and Linker Options # #| Chip Name (Linker) #| You _MUST_ set this to match the board you are using #| type "make clean" after changing this, so all files will be rebuilt #| #| "mk20dx128" # Teensy 3.0 set( CHIP "mk20dx128" ) Just change the CHIP variable to the microcontroller you are trying to build for. NOTE: If you change this option, you will *need* to delete the build directory that is created in the Building sections below. ---------------------- Selecting Modules ---------------------- WARNING: Not all modules are compatible, and some modules may have dependencies on other modules. This is where the options start getting interesting. The Kiibohd Controller is designed around a set of 4 types of modules that correspond to different functionality: - Scan Module - Macro Module - USB Module - Debug Module The Scan Module is where the most interesting stuff happens. These modules take in "keypress data". A converter Scan Module will interpret a protocol into key press/releases. A matrix Scan Module may inherit from the matrix module to scan keypress from a matrix This module just has to give press/release codes, but does have some callback control to other modules depending on the lifecycle for press/release codes (this can be very complicated depending on the protocol). Each Scan Module has it's own default keymap/modifier map. (TODO recommend keymap changing in the Macro Module). Some scan modules have very specialized hardware requirements, each module directory should have at least a link to the needed parts and/or schematics (TODO!). The Macro Module takes care of the mapping of the key press/release code into a USB scan code. Any layering, macros, keypress intelligence/reaction is done here. The USB Module is the output module of the microcontroller. Currently USB is the only output protocol. Different USB output implementations are available, pjrc being the safest/least featureful one. Debug capabilities may depend on the module selected. The Debug Module enables various things like the Teensy LED on errors, debug terminal output. (TODO get true UART working in avr, not just arm) Open up setup.cmake in your favourite text editor. Look for: ### # Project Modules # #| Note: This is the only section you probably want to modify #| Each module is defined by it's own folder (e.g. Scan/Matrix represents the "Matrix" module) #| All of the modules must be specified, as they generate the sources list of files to compile #| Any modifications to this file will cause a complete rebuild of the project #| Please look at the {Scan,Macro,USB,Debug}/module.txt for information on the modules and how to create new ones ##| Deals with acquiring the keypress information and turning it into a key index set( ScanModule "avr-capsense" ) ##| Uses the key index and potentially applies special conditions to it, mapping it to a usb key code set( MacroModule "buffer" ) ##| Sends the current list of usb key codes through USB HID set( USBModule "pjrc" ) ##| Debugging source to use, each module has it's own set of defines that it sets set( DebugModule "full" ) Look at each module individually for it's requirements. There is chip/architecture dependency checking but some permutations of modules may not be tested/compile. There are also CMake options for temporarily selecting modules. But it's easier to just edit the file. e.g. cmake -DScanModuleOverride=<module name> ---------------------- Linux Building ---------------------- From this directory. mkdir build cd build cmake .. make Example output: [master]: cmake .. [...sy/avr-capsense-haata/build](hyatt@901Mas:pts/4) -- Compiler Family: avr -- MCU Selected: at90usb1286 -- Detected Scan Module Source Files: Scan/avr-capsense/scan_loop.c -- Detected Macro Module Source Files: Macro/buffer/macro.c -- Detected USB Module Source Files: USB/pjrc/usb_com.c;USB/pjrc/avr/usb_keyboard_debug.c -- Detected Debug Module Source Files: Debug/full/../led/led.c;Debug/full/../print/print.c -- Configuring done -- Generating done -- Build files have been written to: /home/hyatt/Source/Teensy/avr-capsense-haata/build [master]: make [...sy/avr-capsense-haata/build](hyatt@901Mas:pts/4) Scanning dependencies of target kiibohd.elf [ 12%] Building C object CMakeFiles/kiibohd.elf.dir/main.c.o [ 25%] Building C object CMakeFiles/kiibohd.elf.dir/Scan/avr-capsense/scan_loop.c.o [ 37%] Building C object CMakeFiles/kiibohd.elf.dir/Macro/buffer/macro.c.o [ 50%] Building C object CMakeFiles/kiibohd.elf.dir/USB/pjrc/usb_com.c.o [ 62%] Building C object CMakeFiles/kiibohd.elf.dir/USB/pjrc/avr/usb_keyboard_debug.c.o [ 75%] Building C object CMakeFiles/kiibohd.elf.dir/Debug/led/led.c.o [ 87%] Building C object CMakeFiles/kiibohd.elf.dir/Debug/print/print.c.o Linking C executable kiibohd.elf Creating load file for Flash: kiibohd.hex Creating Extended Listing: kiibohd.lss Creating Symbol Table: kiibohd.sym [ 87%] Built target kiibohd.elf Scanning dependencies of target SizeAfter [100%] Size after generation: text data bss dec hex filename 0 6112 0 6112 17e0 kiibohd.hex 5792 320 852 6964 1b34 kiibohd.elf [100%] Built target SizeAfter ---------------------- Linux Loading Firmware ---------------------- The 'load' script that is created during the build can load the firmware over USB. It uses sudo, so make sure you have the priviledges. (TODO, not complete, avr and arm are different currently, need to be unified) ./load ---------------------- Windows Building ---------------------- TODO ---------------------- Windows Loading Firmware ---------------------- TODO ---------------------- Mac OS X Building ---------------------- TODO ---------------------- Mac OS X Loading Firmware ---------------------- TODO ---------------------- Debugging ---------------------- TODO
kiibohdforce's People
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
๐ Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. ๐๐๐
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google โค๏ธ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.