denvi / candle Goto Github PK
View Code? Open in Web Editor NEWGRBL controller application with G-Code visualizer written in Qt.
License: GNU General Public License v3.0
GRBL controller application with G-Code visualizer written in Qt.
License: GNU General Public License v3.0
Hi,
In full screen, the buttons of the manual control (Jog) are partially hidden.
would it be possible to improve this?
here is a picture: http://pix.slic.it/p/5hr
Thanks
since I had install fresh copy of windows 7 x32, I'm not able to run correctly grblcontrol (except xp version), visualization doesn't work anymore. what else software should I install to get it work?
Hi Denvi,
I've been learning how to use Qt and am modifying grblControl in the process. Everything has been working fine until the last few commits.
I noticed that originally in the source code folder you had many files and 4 subfolders - images, screenshots, shaders and translations. Using this I've had no problems - when I debug in Qt it runs grblControl, connects to the Arduino and i can test everything OK.
However I noticed now with the later versions that you have only some code in your src folder (I assume the main ones which are updated most often) and lots more subfolders. This time everything works OK the first time I run debug. After I close grblControl and press debug again grblControl doesn't connect to the Arduino. It's nearly as if the serial port wasn't closed properly after the last run of debug or maybe the port isn't being open properly. I'm using Qt creator ver 3.5.1. Any idea what could be causing this?
I couldn't locate build instructions and failed to build the program.
The pre-built code doesn't work for me on my 64bit Linux and qmake (which I just guessed is used) complains about serialport and I couldn't see an easy way to use/install it. Maybe it can be put as part of the repository?
you can explain to me as redefinition of speed works? I am admissible I consider that it has to be equal 100% and already a hedgehog from the maximum speed it would be possible to reduce, and now I can't understand as it works
You have configured the calibrator has a bug which leads to malfunction
Hi,
I did the translation in French, but I do not know how to push it on the Git.
I have not your email address to send it.
can you help me ?
How to make so that when sending the task program included the spindle and after 15 seconds, started to carry out the task.
Denvi, congratulations for your project! Loved it! Its interface is very clean and the controls are simple.
I make one fork of your project to study and try to implement some changes, but after reinstalling my Qt Creator 4 times I am unable to compile your code.
I'm using Windows 7 with MinGW, the Qt5.6.0 and Qt Creator 3.6.1.
Please. What is the best way to build and debugger?
Thank you.
I understand that the G2/G3 commands only work in a single fixed plane, but it would be nice if they could be replaced with multiple linear feeds instead of just flat-out replaced with a single linear feed from start to end. Maybe with the existing code setup this won't be so easy, though, but hopefully I'm wrong. There would probably need to be a new settings panel option for adjusting the length or degree tolerance for converting to lines (just like with the visualizer settings).
Another option is to break up arcs into multiple smaller arcs that lie on the XY plane, and proceed in a step-wise fashion from the Z depth. This would just break one arc into multiple arcs that stair-step according to the interpolated heightmap values, perhaps having a tolerance value for this in the settings panel as well that determines the threshold at which an arc is split, and where it is split. This would be a fantastic feature.
Again, I'm not sure it's entirely possible with the existing setup because it appears that the existing setup is limited to simply modifying the existing g-code commands, instead of re-generating an entire program from scratch that would allow for inserting extra g-code commands (like multiple arcs in place of one arc, for instance).
Let me know what you think. I have experience working with the arc command parameters for g-code editing utilities and might be able to help you figure out how to generate the intermediate arcs that would replace a single arc spanning a varied heightmap area.
Thanks!
Good evening,
it would be possible to compile a version for "Mac"?
If it's not too complicated.
Thank you
Hi Denvi,
a. When you press the 'Restore X, Y, Z' button only X and Y are restored. Z should move too.
b. Pressing 'Zero XY' and 'Zero Z' works OK to offset from Machine co-ords. But if you then press 'Reset' to reset the Arduino the current Work co-ords are replaced by the Machine co-ords. Shouldn't the Work co-ords stay the same?
This becomes a problem as follows: let's say you offset & then use 'Zero XY' and 'Zero Z' buttons to set a new 0,0,0 and then send the G-code program. All is OK until you want to quit part way through the program. Pressing and releasing 'Pause' works correctly but when paused if you then press the 'Reset' button to quit sending G-code the Work co-ords become the same as the Machine co-ords and you lose the current Work co-ords.
regards
Peter
Is it possible to use the "check mode" without the CNC is connected ?
Running a gcode program with imperial units leaves grbl in imperial mode, so jogging moves are multiplied by 25.4 until grbl is manually set to metric mode.
I assumed I had to download and extract the tar.gz linux version, and then execute the grblcontrol file. When i do it the program opens, i select the port, it says "connected" but i can't get the CNC to move (shapeoko 3). Is there some dependencies/librairies i am missing?
I'm on linux mint rafaela 64bits. I've been succesfully been able to use my CNC with other grbl controllers in the last two weeks.
Any clue?
Thank you,
Gregory
Hi Denvi,
When I type a command in the bottom right console area of grblControl's screen I just press the Enter key to send it to the Arduino - no problems.
A colleague said this doesn't work for him and when I checked the difference is that I use the Enter key above the Shift key, he normally uses the Enter key on the Numeric Keypad. If it's the same function ie 'Enter' why doesn't grblControl recognise it?
I've tried to run grblControl precompiled under Xubuntu 15.10 x64, but unsuccessful - it does not start. Seems that the problem is the stuff asks for i386 Qt libraries, and I don't know how to install all the necessary things....
Regards,
Sergey
Grbl Control can be used in Raspberry pi 2 model b (RASPBIAN JESSIE)?
thanks.
I just try to build my first PCB using grblControl with heightmap. However, it hasn't milled on the PCB, it just traveled on the air.
I checked the transformed gcode, and study the probe action again. It seems that it will first measure the height of 0,0, and then use the z value for adjustment on the subsequent measurement. For example, if in 0,0 the z value is -0.3, then all subsequent measurement will be adjusted by 0.3. So, the transformed z value in 0,0 is always 0. As a result, it will mill at the position 0.3mm above the target position.
Since my DIY machine cannot recognize the home position, it will reset 0,0,0 to the position whenever the machine started. If it can detect the level in 0,0, that will be great as I have no need to tune the z axis in 0,0 before milling.
And now, it has already measured the difference in all position including 0,0, but it will reduce the value by the measurement in 0,0. So, I have to tune the z position in 0,0 before starting the machine.
Is it possible to use those measured z-value directly without offset the measurement in 0,0?
Thanks a lot.
A colleague was setting up grblControl on another computer and we just discovered a small issue.
Whether an Arduino is plugged in or not, if you select a COM port which isn't connected to the Arduino grblControl displays 'Connected' in the Status box and enables the controls.
This is a little confusing. I can see that the idea is for grblControl to indicate that it is connected to an available serial port but the word 'Connected' implies that it is connected to an Arduino when it really isn't. Would it be possible to display something else rather than the word 'Connected' to make it less confusing and also NOT to enable the controls unless it's actually communicating with an Arduino?
ref: #10 - doesn't seem to apply to my condition.
Caveat: I am a brand new n00b to CNCs and grblControl. I have an extremely low-end PCB CNC. The Arduino is running GRLB 0.9J.
I've figured out how to edit the Stored X/Y/Z in the INI file and have synced that up to be the left-most, front-most, bottom-most corner of the cutter's position. Said another way, the spindle can only be moved up, right, and back from it's current position.
When I enter the program, I confirm both my Machine Coordinates are 0/0/0 and the mouse-hover over Restore X/Y/Z are 0,0,0.
I've also noticed that Aborting a job sends the spindle off in the extreme opposite direction from 0/0/0 to a point that appears to far exceed that range of my very-small machine (4" x 7" x 2" travels). Can this be configured anywhere to recognize the $130 - $132 "max X/Y/Z" parameters as the "Safe" position?
Hi, I cannot open the software on lubuntu latest version, here is a photo of the terminal
Thanks, leonardo
Hi Denvi you have done awesome work with grblcontrol especially with height map probing.So I wonder if it's possible for you to make edge and hole center finder with this probing routines http://www.timeguy.com/cradek/01262579508 ?
I'm hacking away at the code right now to get grblControl to work in imperial units (over here in the states, where my physical tools are in inches) but it would be cool if there was an option in settings to make it so you could work in either metric or imperial, instead of it converting everything to metric no matter what.
Hello, Could you please help me?
I installed grblcontrol on two PCs, one with windows 7 and other Windows 10. In the first, the application works well. In the second pc, the program works well only on the part of commands and file upload, but I can not see anything in the drawing window (aside from the five icons). Re-install the video driver recommended by intel 64 bits, with the same result. What could I do next?
Hi,
I have an issue when I'm using this tool during cutting ply.
I have observed very strange situation - grbl stuck during ordinary works.
It is very annoying when the whole job we need do once again :(
As well as there is no option to restart GRBL if stuck we need reset all and move project again from the begging.
Do you have any idea why I have an issue?
Did you have the same or similar problem?
thx.
Piotr
Hi,
I have a question regarding auto leveling set up.
I'm using DIY copper plate where the thickens of plate is 1.5mm.
How to set up auto leveling option to have correct values when the level measurement will be finished?
I should subtract 1.5mm value from the final values after the test?
Thanks,
Piotr
Hey this is very cool program I am going to test it on my GRBL 0.9j I like the visualizer. I am building a small cnc router machine and also helping retrofit a mill for a friend and a small easy to use interface will help speed up his learning. cheers, Richard
Hi,
thanks for the Wonderful Program.
i would like to create some print screen of the program and add information in you wiki page.
but my computer is in french and your program adopt it and i cannot find a way to change the language to English.
Is there a way to change the language on your software?
Thanks a lot again for grblControl.
Pat Gadget.
Hi,
Great piece of software, so easy to use. Well done!
Just a few small things.
regards
Peter
Hi,
Thanks for your hard work and for your fabulous dev ;-)
This issue post just for ask, if work with Linux, why don't work with Raspian ?
I suppose this is just more of a question about QT, which all of my experience with comes from working with the grblControl code: I cannot figure out how certain things like the feed override slider and the spindle speed are being disabled (ie: 'grayed out') when a program isn't running. I have discovered how most things are being enabled/disabled on the UI, but these things seem to be linked together somehow in a way that I cannot figure out that is controlled by whether or not a program is actively being sent to the CNC.
Thanks :)
Hi,
I've discovered a couple more small quirks with grblControl:
If you replace the G3 line with
G3 X5 Z10 R5
the motion is also correct except the visualiser doesn't display any arc or line.
kind regards
Peter
grblControl rocks, first of all. I just built my X-Carve (waiting for spindle) but I've only been testing it out with my personally modified version of grblControl that runs in imperial, and with a few graphical and keyboard jogging changes.. I will probably not bother using any other GRBL controller program with it because grblControl is exactly what I would make if I were to write my own program from scratch (which I was just about to do when I discovered grblControl).
so, I don't have homing switches on my machine, or homing enabled on GRBL, so 'home' is just floating wherever (somewhere outside my house, apparently)
when I run a program and hit the abort button, it seems to perform the Restore XYZ button's function (I assume) and sends the machine off wherever it thinks it should go. What would be great is if the abort button just sent the machine back to wherever it was when it started the program that it was running in the first place, perhaps moving to safety Z first and then rapiding to the original start position.
I'm going to try to hack away at the code and figure this out myself but I figured I may as well contribute my ideas to the project for the project's benefit as a whole.
thanks for sharing grblControl with us, I am working on a project that uses G-code programs with tens of thousands of lines of code, and all the other programs I have tried came to a crawl when I would load my G-code program into them because they were written using tons of external garbage and weren't running natively on my CPU.
please keep up on grblControl! I have been promoting it on various forums telling people it is the best program I have found, because it is true! With the heightmapping feature you're right up there with the best of the other programs.
Hi,
On my Windows 7 PC the program works fine, visualization works correctly. But on this laptop the window is blank: no text, no coordinate origin, no FPS etc.
Please see attached screenshot.
I thought it has to do with graphic card compatibility, so I have tried changing graphics settings to no avail. On a side note, when I change graphics to 32 bit mode, the application crashs.
I am using a Compaq CQ20 laptop running Windows 7. All drivers are originals from the manufacturer.
Can you please tell me what the problem would be?
Dear Denvi,
I noticed a different behavior when I press the reset button of the program and when I hit the reset button on the Arduino Nano pin A0
In particular, reset from the program works perfectly, but I just get a message "error: Alarm Lock" in the console and the status doesn't changes using the hardware Reset/Abort key (A0)
Similar behavior using "Hard limit"
Thank you
Greetings, I love the program, finally got GRBL clients to work with my Carvey after changing the report line. Carvey uses gCarving fork (GRBL 1.0 based), I only had to change the message the client expects to read the GRBL version and know that it has "booted".
I can do many things now with GRBL control, however when I open the carvey door / front lid, it outputs a message [Check Door] and Grbl control crashes.
A fix would be awesome. Thanks a lot !
Thanks for sharing the software, really excellent.
I like the feature of heightmap very much, it solve the problem of leveling after re-assembly. Thank you very much.
However, when I try to save the gcode, it will save the original version instead of the adjusted version.
As I have built an off-line milling tools with my CNC, so that it can use the file in SD card without computer. May I know if it's possible to save the adjusted gcode to a file, so that it can be used for off-line milling.
Thanks in advance.
Hello. Thank you for your project and the work you have done. I’m new to CNC and I’m beginning to use my new CNC with your software.
I have a question for you, I didn’t understand myself:
In version 0.8.3 Restore XYZ key did move the CNC to home position (relative) just for X and Y coordinates. Why not Z?
And now, with new version 0.8.4, this key just restore offset and don’t move CNC
How can I move the CNC step motors to home (relative 0,0,0)?
Many thanks Roberto
Hi there!
i´m currently working with foam cutting machines,grbl is perfect for this kind of aplications and so it grbl Control, but for some people around here,english is still a limited subject.
Is there any chance to get any Xml so i can be able to translate it to spanish?
Thanks in advance!
Tried downloading the pre-built binary and it fails at command line execution.
There is an Error, but the message that comes after doesn't show anything intelligible.
Also, tried cloning the repo to build it myself, but no make files.
How should I build this codebase on my Ubuntu machine?
Thanks for your guidance.
thanks in advance
Peter
This is a rather quirky issue. I'm using grblControl to control my home built laser engraver. When I create gcode with the extension that comes built in with Inkscape, everything works great (except I cannot automate the multiple passes). When I create gcode using J Tech photonics inkscape extension (which can automate multiple passes), and load it in grblControl, I cannot see any of the lines that the engraver is supposed to engrave (unlike the one with the one built in with Inkscape which shows me all the paths). grblControl in this case does finally give the needed output, it just does not show the paths on screen. Any ideas?
Hi there!
I just saw some screen shots of grblControl, and it looks great! Unfortunately, I am unable to start the program, because of the following error:
I am trying to use grblControl on my old laptop running Windows XP (if that matters). Can you help?
Thanks in advance
jrhansen :-)
Hi,
I have no visualization. I tried check mode, also changed colors.. Nothing helped. Could You please help me?
try launch this app on win 10. not working.
A declarative, efficient, and flexible JavaScript library for building user interfaces.
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google ❤️ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.