binnes / wifimeshraspberrypi Goto Github PK

I successfully created the gateway and second nodes. However after turning the second node into a Bridge it doesn't get a 192.168.199.x address and is unable to ping the gateway (192.168.199.1). Anything connected to eth0 on the Bridge cannot reach the internet either.

Any suggestions?

Thanks for the tutorial, it was very helpful.
Setting up the mesh and a gateway was a breeze. But I ran in to a problem.
I had issues pinging and reaching the nodes in the mesh although I successfully set up the mesh network according to your instructions.

I would like to mention that changing the MTU value of the host adapter (wlan0) to 1532 and not setting a MTU value on the bat0 adapter solved my problem with communicating across the mesh.

I hope this can be of help to someone experiencing the same issues I did. In my case only batctl ping worked, normal ping did not. That is until I changed the mtu values as described above.

Figured it out, I was indeed being dumb

I successfully implemented the gateway however the bridge doesn't seem to work, what do i do.

Thanks for making this tutorial available I found it very useful.

I set up a bridged mesh network to extend my home lan to a number of IOT sensor devices (Pi Zero W) that are in range of each other but not all can see my router AP.

I follower your guide which worked, but encountered the issue mentioned here: #6
ie errors when trying to get neighbours/origins/stats etc.

So I built batctl to match the batman-adv version as suggested and my mesh stopped working, or rather the mesh came up fine, but no nodes were able to get an IP address so became unreachable.

A diff of batctl 2019.0 vs 2020.4 showed the gw_mode client/server options were only added after 2019.0 so I removed the line "sudo batctl gw_mode client" and everything started working again.
I guess 'gw_mode client' instructs the mesh to look specifically for a gateway server and supresses instead of passing on DHCP requests?

ETHERNET works perfectly however i am trying to implement the one in part 2 using hotspot , everything is working fine until i get to the verification step where i run ifconfig in the gateway node and i dont see the wlan1 interface where iwconfig shows wlan1 essid if/any.
Also when i hover over the wifi connection on my rpi desktop using mouse and keyboard i get the message connection to dhcpcd lost.

Hi binnes,
I've seen your work and completed part 1 with no problems. But moving to part 2, i dont really understand what you meant by saying "replace wlan0 with wlan1 in all the previous configuration completed in part 1 and switch wlan0 and wlan1 in the following configuration."
For example:
sudo nano /etc/network/interfaces.d/wlan0
Do i have to create another file "wlan1" and set the content with wlan1 or i just need to replace wlan0 with wlan1 in "wlan0" file?
And do i have to replace wlan0 with wlan1 for just the gateway rapberrypi or all of the raspberrypis ?
Thank you!

Thanks for putting this together. I thought it was very clean to follow. I thought I had a PI setup as a gateway. Only minor place I diverged is I ended up putting the start script in root's home directory, but I accounted for that in rc.local.

I've got an HDMI monitor hooked up to the PI, and on rebooting I can see the above error come up when it hits rc.local. Actually, the whole message text is: Error - interface bat0 is not present or not a batman-adv interface.

I tried running this as root after boot up and got the same message.

Since I haven't yet configured another node, (cause I got to run out and buy some more microSD cards) is that in play here? Or do I need to back up and figure out this error next?

Regards,

Neal

I have two drones, 1 gateway and the other is bridge, i have a pozyx device attached to the rpi where it returns to me the xyz coordinates in a 3d plane. How do i send commands or recieve info from the drones on my laptop whether its data or photos.

I am currently implementing the wifi bridge part so its not over yet however I want to know what to expect

Sorry if this seems like a dumb question.
But can I setup multiple Access points using the same SSID? One AP on each Mesh node.

it was really helpful i manage to build a network i am using 3 pi one is gateway and another one is bridge they both are connected to each other but the third pi is connecting and moreover i want to access internet from all three pi for the third pi I follow all the commands in the file name PMESH. But i am unable to see third pi and cant access internet from my pi.

Hello there,

Thanks for your amazing guide!
I ran into some trouble with batctl.

Running sudo ~/start-batman-adv.sh results in an error:
Error - interface bat0 is not present or not a batman-adv interface
Unfortunately I couldn't find any solution on the web, so I turn to you :)

I followed your guide step by step and double-checked the files. Already after the first setup (Part 1 - Mesh Networks), this error appears when running sudo batctl gw_mode client.

It happens on a Raspberry Pi 4B as well as on the 3B+. Latest Raspberry OS Lite (Buster).

Greets,
Tom

Hi, thanks for sharing this, it's been of great help !

Everything works fine, but I've been since some days trying to set up the gateway node also as an AP. I think it can be done but i'm facing some issues, if you had some documents to share or anything it would be of great help !

So far i've been able to either set up a functionnal mesh without an AP on the gateway or an AP on the gateway node but the bride nodes couldn't connect anymore and the client (smartphone) could connect to the AP BUT with an address given by the ethernet connection, while I need the client to get an address from the gateway.

Thanks for any help you could provide !

the gateway has been setup successfully (part2) however when i try to implement the wifi bridge model, i seem to have all the wlan connections disappear.
Do i have to plug in a usb dongle aswell to the rpi just like the gateway?
Is this normal ?
how to actually connect the bridge to the gateway and start communicating?

Hello Brian,

Creating my request as a new issue. Apologies, earlier I was posting on a closed thread.
My hardware and software details are as following
Gateway
Raspberry Pi 2 Model B Rev 1.1
5.10.11-v7+ #1399 SMP Thu Jan 28 12:06:05 GMT 2021 armv7l GNU/Linux
USB WiFi (Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter)

Bridge
Raspberry Pi 4 Model B Rev 1.2
5.10.11-v7l+ #1399 SMP Thu Jan 28 12:09:48 GMT 2021 armv7l GNU/Linux
On-board WiFi

Issue details

Sometimes back I followed your instructions and successfully created the mesh network
But I tried today again and it shows me error "wlan0: error reading status".

I have closely tried all the instructions twice with a fresh image from Raspberry site.
I am configuring one Pi for Gateway and another for Bridge.
Followed the instructions very closely in Part1.
But it shows same error like this

pi@rpi-brg-4gb:~ $ sudo batctl if
wlan0: error reading status

my gateway looks like this

pi@rpi-gtw-1gb:~ $ ifconfig
bat0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1468
inet 192.168.199.1 netmask 255.255.255.0 broadcast 192.168.199.255
inet6 fe80::36c5:e5f6:4e13:9df8 prefixlen 64 scopeid 0x20
ether 1e:1a:0c:49:4c:81 txqueuelen 1000 (Ethernet)
RX packets 21 bytes 1460 (1.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 3 bytes 304 (304.0 B)
TX errors 0 dropped 45 overruns 0 carrier 0 collisions 0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.34 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::d6aa:4ac5:b976:548a prefixlen 64 scopeid 0x20
ether b8:27:eb:9f:ee:3b txqueuelen 1000 (Ethernet)
RX packets 1187 bytes 59140 (57.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 117 bytes 14893 (14.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10
loop txqueuelen 1000 (Local Loopback)
RX packets 95 bytes 7546 (7.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 95 bytes 7546 (7.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::7edd:90ff:fe47:4507 prefixlen 64 scopeid 0x20
ether 7c:dd:90:47:45:07 txqueuelen 1000 (Ethernet)
RX packets 117 bytes 9729 (9.5 KiB)
RX errors 0 dropped 4 overruns 0 frame 0
TX packets 133 bytes 13669 (13.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

pi@rpi-gtw-1gb:~ $ iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11 ESSID:"call-code-mesh"
Mode:Ad-Hoc Frequency:2.412 GHz Cell: EE:99:7A:6C:F5:07
Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Power Management:on

bat0 no wireless extensions.

pi@rpi-gtw-1gb:~ $ sudo batctl if
wlan0:

pi@rpi-gtw-1gb:~ $ sudo batctl n
Error - interface bat0 is not present or not a batman-adv interface

my bridge looks like this

pi@rpi-brg-4gb:~ $ ifconfig
bat0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1468
inet6 fe80::8a6:7ff:feb8:a14a prefixlen 64 scopeid 0x20
ether 0a:a6:07:b8:a1:4a txqueuelen 1000 (Ethernet)
RX packets 33 bytes 1386 (1.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 3557 bytes 213767 (208.7 KiB)
TX errors 0 dropped 225 overruns 0 carrier 0 collisions 0

br0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1468
inet 192.168.1.4 netmask 255.255.255.0 broadcast 192.168.1.255
inet6 fe80::8a6:7ff:feb8:a14a prefixlen 64 scopeid 0x20
ether 0a:a6:07:b8:a1:4a txqueuelen 1000 (Ethernet)
RX packets 3995 bytes 197842 (193.2 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 286 bytes 31309 (30.5 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::dea6:32ff:feb7:dd6b prefixlen 64 scopeid 0x20
ether dc:a6:32:b7:dd:6b txqueuelen 1000 (Ethernet)
RX packets 4031 bytes 257826 (251.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 331 bytes 33904 (33.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10
loop txqueuelen 1000 (Local Loopback)
RX packets 8 bytes 480 (480.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 8 bytes 480 (480.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet6 fe80::dea6:32ff:feb7:dd6c prefixlen 64 scopeid 0x20
ether dc:a6:32:b7:dd:6c txqueuelen 1000 (Ethernet)
RX packets 94 bytes 6715 (6.5 KiB)
RX errors 0 dropped 1 overruns 0 frame 0
TX packets 359 bytes 37300 (36.4 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

pi@rpi-brg-4gb:~ $ sudo brctl show
bridge name bridge id STP enabled interfaces
br0 8000.0aa607b8a14a no bat0
eth0

pi@rpi-brg-4gb:~ $ sudo batctl if
wlan0: error reading status

pi@rpi-brg-4gb:~ $ sudo batctl n
Error - interface bat0 is not present or not a batman-adv interface.

Please suggest me what could be the possible reason for this.
your guide is excellent material on mesh networking.
Thanks for educating the community on mesh networking.

Regards
Leo

Hello I have the gatewawy working perfectly using usb dongle not ethernet, same goes for the bridge access point using usb dongle with the exception that once i reboot my bridge node I get the NO WLAN INTERFACE FOUND and I cant seem to be able to access the rpi through putty anymore and so I have to use a monitor setup.

I tried all sorts of commands I could find from playing around with dhcpcd or even editing the WPA_supplicant but nothing seems to work.

My question is this supposed to happen, should a bridge node not be able to access the internet? aka my wifi mobile hotspot?

Also when I try running the sudo batctl n on either the gateway or the bridge I dont seem to find neighbours as mentioned.