Comments (9)
If your home network on which encryption is used is saved in the Wi-Fi settings, then when you turn on emergency mode, you will be connected to this network with encryption.
I see no practical point in creating an access point from ZigStar. Only for configuration, and there is no point in encryption.
You can allow ping from the local network on your gateway, all problems will be solved. There are no security issues with this.
Indeed, as one of the ways - use another device instead of a gateway.
Thanks for your advice to the community.
Perhaps in the future I will add a similar functionality.
Thanks for the ideas and feedback.
from zigstargw-fw.
duplicate #13
from zigstargw-fw.
Just wanted to leave a quick workaround for this "bug".
I (very) recently got myself a ZigStar device, and had the exact problem. I did manually configure the network and then had the problem with the emergency wifi enabled.
first of all, it would be better to have a configurable emergency wifi with encryption, but that might not be able on this device.
BUT to fix it until the option you mentioned is implemented, i did just enter a device as the gateway that does not route trafic (because i don't see any need for the zigstar device to reacht the internet) but that is always online. In my case i used a NAS device, but could be anything.
Maybe you could let us manually choose which device to ping to check if the device is up.
Also thanks for your work!
from zigstargw-fw.
I think many people are misunderstand difference between emergency and normal wifi connection mode.
Emergency is WIFI Access point, right?
And if both wifi connection and ethernet is configured and present -- they both will be connected without emergency (in normal mode).
from zigstargw-fw.
ZigStar is not recommended to use wifi in working mode. But it is possible.
Emergency mode turns on wifi in case of loss of wired connection.
If you have saved your network settings, ZigStar will first try to connect to it.
If successful, it will be connected as a client to your network until the wired connection is resumed.
If the wireless network is not available or no settings are saved, then ZigStar raises its access point.
After resuming the wired connection, it turns it off.
from zigstargw-fw.
Okay, so it works really strange now.
My gateway\router is responding to ping requests:
% ping 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
64 bytes from 192.168.1.1: icmp_seq=0 ttl=64 time=3.079 ms
64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=3.306 ms
Here is my zigstar-gateway status, it connected simultaneously to wifi and ethernet (same network and gateway\router):
https://ibb.co/wMs4JR8
"Disable emergency mode (AP)" is disabled (not checked). Also here is config:
{"enableWiFi":1,"ssid":"****","pass":"*******","dhcpWiFi":1,"ip":"","mask":"","gw":"","disableEmerg":"0"}
According to Home Assistant status of zigstar-gateway "Emergency mode = Off".
But it connected to wifi and ethernet same time.
from zigstargw-fw.
I don't see anything strange.
You have the checkbox Enable Wi-Fi client mode checked
Therefore, there is a connection to the wifi, regardless of the state of the wired connection.
from zigstargw-fw.
Oh, missed it! thanks a lot! Without "Enable Wi-Fi client mode" works as expected - connects to wifi on ethernet failure.
from zigstargw-fw.
from zigstargw-fw.
Related Issues (20)
- Web interface freezes while reconnecting to MQTT HOT 1
- 'dict object' has no attribute 'ow_temperature' when rendering '{{ value_json.ow_temperature }}' HOT 11
- Unable to turn off emergency WiFi HOT 4
- Fails to boot after power outage. HOT 4
- Ability to reset login password HOT 3
- Ethernet shows disconnected after update to 0.6.8 HOT 14
- wich bin file should i use ? full or not full ? HOT 1
- Cannot connect to mosquitto mqtt running as HA addon HOT 7
- DS18B20 sensor is not queried HOT 2
- Update available - sensor for Home Assistant HOT 2
- Include BTHome gateway HOT 1
- Dallas DS18b20 sensor suddenly only 0CĀ° HOT 3
- Two indentical coordinators conflict HOT 2
- Flash cc2538//cc2652 from WebUI HOT 4
- Delay on outgoing packets send while high load on Zigbee network HOT 2
- [Request] Support disabling Leds HOT 1
- Compile firmware error HOT 1
- Unable to reconnect WIFI automatically when WIFI AP restarts HOT 1
- ZigStar Ethernet GW: get MQTT socket state and reboot cmd HOT 5
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
š Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. ššš
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ā¤ļø Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from zigstargw-fw.