Comments (11)
Mmmm, yes. Enable the checkbox in settings, so the plugin doesn't send m420 again and instead send G29
from octoprint-smartabl.
Correct, that should work. You don't need to modify your slicer settings. SmartABL should recognize M420 and trigger ABL according to your settings.
Thank you! I will test it with a couple of fast prints and see if it works :) it's a great plugin
from octoprint-smartabl.
Noted! I'll add that to the next release
from octoprint-smartabl.
Hi, sorry for the delay, I've been pretty busy.
I've added a prerelease for 0.1.4, do you mind checking it? It shows a counter under the print information with the number of prints until ABL is triggered. I've fixed the bug with M420 not triggering ABL.
from octoprint-smartabl.
Hi, sorry for the delay, I've been pretty busy.
I've added a prerelease for 0.1.4, do you mind checking it? It shows a counter under the print information with the number of prints until ABL is triggered. I've fixed the bug with M420 not triggering ABL.
I'll check it out! And write a follow up if I encounter anything weird. Out of all the plugins I have, I think yours is the most useful so keep up the fantastic work and take care :)
from octoprint-smartabl.
Mmmm, yes. Enable the checkbox in settings, so the plugin doesn't send m420 again and instead send G29
This you mean?
Do I also have to add G29 in prusaslicer?
from octoprint-smartabl.
Correct, that should work. You don't need to modify your slicer settings. SmartABL should recognize M420 and trigger ABL according to your settings.
from octoprint-smartabl.
Okay yes it works! Thank you :) however I'm wondering about one other thing.
When the abl has finished, it goes straight to the printing process and therefore i can't manually adjust the bed or set the offset like you can when you do abl normally.
Im sure there's a command for this.
from octoprint-smartabl.
Mmmm, that's not what I do. I usually send G29 to generate the mesh and start printing, the printer compensates the Z-height according to the mesh generated with G29, without physically modifying the bed. I only do manual leveling using tramming wizard (marlin), but I do it occasionally, when the points in the mesh are higher/lower than 0.1mm.
How do you use ABL?
from octoprint-smartabl.
I see. Well it's not a problem at all but this is how I usually do it :)
I usually run the abl and then I check each corners with a 0.1 blade and adjust if needed.
I know its not needed each time and I've actually started to not do this each time and trust the probe but sometimes I do this, because I have the probe at a bad location (ender s1 pro) it won't probe the whole bed and thus miss some of the bad spots.
Every now and then when needed, before I manually run the abl, I first use a digital dial indicator and make sure the bed is 100% level and then I run the abl and then I do manual checking after that. Since I started doing this, my first layers are amazing. I have the silicone rubber spacer instead of the springs so I do this maybe only once a month.
And btw, would it be possible to include some kind of counter that tells you how many prints before it will trigger the abl?
from octoprint-smartabl.
Closed as released in https://github.com/scmanjarrez/OctoPrint-SmartABL/releases/tag/0.1.4
from octoprint-smartabl.
Related Issues (20)
- [Help needed] Looking for Klipper users to make SmartABL compatible HOT 15
- [Request] Special behavior short short prints HOT 4
- [Request] Ability to add other GCODES to be stripped out if leveling is skipped HOT 40
- [Request] ABL Misfire HOT 10
- ABL every time you start printer? HOT 80
- ABL every time (N3P) HOT 6
- Z Steppers Auto-Alignment (G34) HOT 5
- SmartABL disabling due to "unsupported firmware" but running Klipper HOT 10
- M420 S1 and then print just stalls HOT 33
- Add custom gcodes to be tracked, instead of the hardcoded ones HOT 1
- SmartABL continually executes ABL on every print if ABL not saved to EEPROM HOT 26
- [Request] Bed Visualizer compatibility HOT 11
- [Request] Reset smartabl when bed leveling is run not through a file. HOT 3
- Printer is stuck HOT 4
- Still shows version 1.2.0 after updating to 1.2.1 HOT 2
- Cancel button hides behind SmartABL buttons HOT 1
- SMartABL not working after update to Octoprint 1.9.1 HOT 12
- SamrtABL seems to be non functional on my system HOT 23
- Improve Plugin Description by explaining the Acronym ABL at least once
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from octoprint-smartabl.