Problems detecting SP30 on TTGO_T7 about canairio_firmware HOT 2 CLOSED

== CanAirIO Setup ==

-->[OLED] display config ready.
-->[INFO] ESP32MAC: 98:F4:AB:6D:4C:52
-->[INFO] Revision: r799
-->[INFO] Firmware: 0.3.5
-->[INFO] Flavor : TTGO_T7
-->[INFO] Target : dev
-->[INFO] Detecting sensors..
-->[INFO] PM sensor configured: 2
-->[I2CS] detected AM2320 sensor :)
-->[INFO] Detection sensors FAIL!
-->[WDOG] watchdog config to check each 120 seconds.
-->[BTLE] GATT server ready. (Waiting for client)
-->[INFO] InfluxDb API: 0
-->[INFO] CanAirIO API: 0
-->[BTLE] device client is connected.
-->[BTLE] device client is disconnected.
-->[BTLE] start advertising..
-->[BTLE] device client is connected.
-->[CONF] set device name to: PM25_4C52_SP30
-->[CONF] WiFi credentials saved!
-->[WIFI] connecting to TunalSensores..............................fail!
-->[E][WIFI] disconnected!
-->[CONF] updated location!

from canairio_firmware.

-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:72.000000% T:22.700001°C
-->[CONF] request: {
"act": "rbt",
"cmd": "20556",
"aenb": false,
"denb": false,
"i2conly": false,
"ienb": false,
"wenb": false,
"wmac": 0,
"wsta": false
}
-->[CONF] reboot..
ets Jun 8 2016 00:22:57

rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0018,len:4
load:0x3fff001c,len:1044
load:0x40078000,len:10124
load:0x40080400,len:5828
entry 0x400806a8

== CanAirIO Setup ==

-->[OLED] display config ready.
-->[CONF] debug is enable.
-->[INFO] ESP32MAC: 98:F4:AB:6D:4C:52
-->[INFO] Revision: r799
-->[INFO] Firmware: 0.3.5
-->[INFO] Flavor : TTGO_T7
-->[INFO] Target : dev
-->[INFO] Detecting sensors..
-->[INFO] PM sensor configured: 2
-->[SENSORS] debug is enable.
-->[SENSORS] sample time set to: 5
-->[SENSORS] temperature offset: 0.00
-->[SENSORS] forced only i2c sensors: 0
-->[PMSENSOR][UART] detecting SPS30 PM sensor..
-->[SPS30] starting SPS30 (UART) sensor..
Sending: 0x7E 0x00 0xD1 0x00 0x2E 0x7E
-->[E][SPS30] Could not probe with SPS30.
-->[SPS30] starting SPS30 (UART) sensor..
Sending: 0x7E 0x00 0xD1 0x00 0x2E 0x7E
-->[E][SPS30] Could not probe with SPS30.
-->[SPS30] starting SPS30 (UART) sensor..
Sending: 0x7E 0x00 0xD1 0x00 0x2E 0x7E
-->[E][SPS30] Could not probe with SPS30.
-->[SENSORS] not found any PM sensor via UART
-->[SENSORS] trying to load I2C sensors..
-->[SPS30] starting SPS30 (I2C) sensor..
I2C Sending: 0xD1 0x00
Error: Received NO bytes
I2C Received: length: 0

Error during reading from I2C: 0x51
-->[E][SPS30] Could not probe with SPS30.
-->[GCJA5] starting PANASONIC GCJA5 sensor..
-->[AM2320] starting AM2320 sensor..
-->[I2CS] detected AM2320 sensor :)
-->[SHT31] starting SHT31 sensor..
-->[BME280] starting BME280 sensor..
-->[BME680] starting BME680 sensor..
-->[AHT10] starting AHT10 sensor..
-->[SCD30] starting CO2 SCD30 sensor..
-->[INFO] Detection sensors FAIL!
-->[WDOG] watchdog config to check each 120 seconds.
-->[WIFI] connecting to TunalSensores........................ done.
-->[WIFI] connected!
-->[WIFI] 192.168.5.124
-->[WIFI] publish interval: 10 sec.
-->[INFO] ready for OTA update.
-->[FOTA] not need update
-->[CONF] response: {
"dname": "PM25_4C52_SP30",
"stime": 5,
"stype": 2,
"wenb": true,
"ssid": "TunalSensores",
"ienb": false,
"ifxdb": "canairio",
"ifxip": "influxdb.canair.io",
"ifxpt": 8086,
"aenb": false,
"apiusr": "",
"apisrv": "",
"apiuri": "",
"apiprt": 80,
"denb": true,
"i2conly": false,
"toffset": 0,
"lskey": "",
"wmac": 20556,
"wsta": true,
"vrev": 799,
"vflv": "TTGO_T7",
"vtag": "dev",
"vmac": "98:F4:AB:6D:4C:52"
}
-->[BTLE] GATT server ready. (Waiting for client)
-->[INFO] InfluxDb API: 0
-->[INFO] CanAirIO API: 0
-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:72.000000% T:22.799999°C
-->[BTLE] device client is connected.
-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:73.199997% T:22.799999°C
-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:81.400002% T:22.799999°C
-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:80.599998% T:22.799999°C
-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:78.800003% T:22.799999°C
-->[SENSORS] able data from UART sensors: 0
-->[AM2320] read > done!
-->[SENSORS] PM1:000 PM25:000 PM10:000 CO2:0000 CO2humi:0.000000% CO2temp:0.000000°C H:77.699997% T:22.900000°C

from canairio_firmware.