Comments (11)
JimPBarber
commented on July 16, 2024
3
Run a PID calibration.
http://marlinfw.org/docs/gcode/M303.html
https://www.youtube.com/watch?v=APzJfYAgFkQ
Your software need to know how to handle the new hot end.
Jim.
…On Mon, Aug 26, 2019 at 12:55 PM roon4660 ***@***.***> wrote:
I am in a quandary with my Ender 3 pro which I’ve had very good success
with the past few months. I upgraded my hot end and it worked fine for
about a day and then started to behave strangely. When I preheated the
nozzle to 250 degrees C which it could always do very quickly I noticed
that it was pooping out at 184 C and then will eventually go up to 195 and
flutter down and up from there. I keep trying things like checking the
thermistor and it’s easy to check the heater. Everything is plugged in all
right. It was working now it’s not. Is it something to do with the computer
program? I have version 1.1.6 Marlin firmware. I noticed I can set it to
190 C and it will go there and stay there with it’s up and down a few
degrees. It just can’t get up to what I want.
Larry R.
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#41?email_source=notifications&email_token=AMRFECECFHRYKO4DRMS6THDQGQYLZA5CNFSM4IPUVZDKYY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4HHO45TA>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AMRFECFPLPVVE77O3YT3DBDQGQYLZANCNFSM4IPUVZDA>
.
from ender-3.
roon4660
commented on July 16, 2024
1
Joshua Rising I am preparing to go to my friend's chalet till Saturday so I will get into this when I get back if you are still so kind. Thank you.
Larry R.
On Monday, August 26, 2019, 04:41:08 p.m. GMT-4, Joshua Rising <[email protected]> wrote:
Check for continuity on both ends of the wires and the voltage on the controller board versus the voltage going into the hotend.
I have a multimeter but what do I check? Thanks for your response. Larry On Monday, August 26, 2019, 04:18:40 p.m. GMT-4, Joshua Rising [email protected] wrote: It's possible that it has a short. Have you checked the connection with a mutimeter? — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub, or mute the thread.
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub, or mute the thread.
from ender-3.
zero4281
commented on July 16, 2024
It's possible that it has a short. Have you checked the connection with a mutimeter?
from ender-3.
roon4660
commented on July 16, 2024
I have a multimeter but what do I check? Thanks for your response.
Larry
On Monday, August 26, 2019, 04:18:40 p.m. GMT-4, Joshua Rising <[email protected]> wrote:
It's possible that it has a short. Have you checked the connection with a mutimeter?
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub, or mute the thread.
from ender-3.
zero4281
commented on July 16, 2024
Check for continuity on both ends of the wires and the voltage on the controller board versus the voltage going into the hotend.
I have a multimeter but what do I check? Thanks for your response. Larry On Monday, August 26, 2019, 04:18:40 p.m. GMT-4, Joshua Rising [email protected] wrote: It's possible that it has a short. Have you checked the connection with a mutimeter? — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub, or mute the thread.
from ender-3.
roon4660
commented on July 16, 2024
I am so happy to see your reply to my "quandary". I am packing to leave till Saturday and can only try this when i get back. I hope your patience holds till then.
Larry R.
On Monday, August 26, 2019, 06:35:26 p.m. GMT-4, JimPBarber <[email protected]> wrote:
Run a PID calibration.
http://marlinfw.org/docs/gcode/M303.html
https://www.youtube.com/watch?v=APzJfYAgFkQ
Your software need to know how to handle the new hot end.
Jim.
On Mon, Aug 26, 2019 at 12:55 PM roon4660 ***@***.***> wrote:
I am in a quandary with my Ender 3 pro which I’ve had very good success
with the past few months. I upgraded my hot end and it worked fine for
about a day and then started to behave strangely. When I preheated the
nozzle to 250 degrees C which it could always do very quickly I noticed
that it was pooping out at 184 C and then will eventually go up to 195 and
flutter down and up from there. I keep trying things like checking the
thermistor and it’s easy to check the heater. Everything is plugged in all
right. It was working now it’s not. Is it something to do with the computer
program? I have version 1.1.6 Marlin firmware. I noticed I can set it to
190 C and it will go there and stay there with it’s up and down a few
degrees. It just can’t get up to what I want.
Larry R.
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#41?email_source=notifications&email_token=AMRFECECFHRYKO4DRMS6THDQGQYLZA5CNFSM4IPUVZDKYY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4HHO45TA>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AMRFECFPLPVVE77O3YT3DBDQGQYLZANCNFSM4IPUVZDA>
.
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub, or mute the thread.
from ender-3.
wanderling
commented on July 16, 2024
Attach an incandescent bulb rated for the voltage you are monitoring (ie: 12v bulb for 12v system. 24v bulb for 24v system. etc.) to the heater leads in parallel with the heater. If temps drop while the bulb stays lit, suspect heater. If bulb goes out AND temps drop, suspect control hardware (thermistor, connections, wires). If all of that looks fine, check the control board itself REAL carefully. Look for broken or dull solder connections, or overheating components. Good idea to reset the Ender 3 to factory defaults first.
from ender-3.
roon4660
commented on July 16, 2024
I have my ender 3 pro connected to my macbook pro with Marlin 1.6.1 installed and my new usb cable and cannot seem to tether it even with printrun for mac installed. I would like to run the PID setup but my mac can't find the ender. Should I try octoprint? A slicer?
from ender-3.
roon4660
commented on July 16, 2024
I made an error I have a Creality 1.1.6 board. I'm not sure what version of Marlin is installed. I don't know what it wants for a "port". I tried com2 and usb2 and variations, but have no results, just errors.
from ender-3.
roon4660
commented on July 16, 2024
I have the bootloader installed(flashed) in my ender 3 pro and I have the printer connected to my macbook pro.
Using Printrun for mac the nozzle temperature to 250 C and at about 190 C it failed. This is the error message
in Printrun.
Setting hotend temperature to 250.000000 degrees Celsius.
Error:Heating failed, Heating failed
Printer halted
please reset.
I don't even know if I should try to set the PID at 190 or what?
from ender-3.
steenerson
commented on July 16, 2024
Hi @roon4660, is this issue ongoing or can we close it out?
from ender-3.
Related Issues (20)
- are there any .pdf drawings for the Ender 3 pro? HOT 1
- Creality3D V1.1.4 + MKS LCD12864A V1.0 screen not working
- Reading PDF Drilling HOT 2
- Ender 2 Pro (Creality 4.2.3 mainboard)
- Ender 3 V2 "Z movement Stop working"
- Help Needed with Printing HOT 30
- X motor cover/limit switch holder
- All .dwg files are corrupted and unreadable by AutoCAD.
- Ender 3 won't maintain printing temp. - Electrical/firmware?
- ender 3 - temp issue on display with bed and nozzle temp PLZZZZ HELP!!! HOT 15
- Ender 3 Filament slipping, tried everything to fix help plzz HOT 18
- Nozzle temp keeps dropping and Im not sure why Plllz help!! HOT 8
- output specs of the Bed and Fan+ connections on a V4.2.7 board.
- Ender 3 pro not heating for print HOT 1
- Ender 3 pro heating problem HOT 1
- Can I reverse diode on +5V USB HOT 1
- Ender 2 pro vith V2.4.S4 mainboard
- Ender 3 pro extruder plastic support broken - looking to change the extruder? HOT 3
- Princore pellet extruder
- Thermal runaway
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from ender-3.